Jump to content
SAU Community

Recommended Posts

Hey...still need this stuff to go. Here are the new prices again along with an update of the things still left. I can organise postage for some items under request

NEW PRICES:

1. After Market wing $60

2. Rear Boot and S1 Wing/stop light $65

3. Side Skirts $35 each or $60 pair - SOLD

4. Rear S2 Garnish $15 - SOLD pending payment

5. Drivers Side S1 Head Light $15

6. Dash Surround $50

7. Drivers Side Window surround and Controls $30

8. Steering Wheel $10

9. Hicas Control $15

10. Rims - SOLD

11. Rear Bumper S1 (This is different to the first one I sold - has 4 holes in it from reverse sensors - slightly damaged) - $20

SOLD ALREADY: Rims, Side Skirts, Rear Bumper, Front Grill, Indicators

PM me anytime or call mobile. Check the first post for pictures and information.

Cheers

Hey Mate, i need the smallest thing for my r32 (hoping its the same in the r33)! I need the small black round connector that the low beam bulb plugs into in the front headlight?? is the stupidest thing but i cannot get one anywhere!! hope you have one, cheers

Hey Mate, i need the smallest thing for my r32 (hoping its the same in the r33)! I need the small black round connector that the low beam bulb plugs into in the front headlight?? is the stupidest thing but i cannot get one anywhere!! hope you have one, cheers

I am not sure if the R33 is the same. But I have both round connectors that I think you are talking about on the head light. The head light is only $15 for the whole thing if you want it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...