Jump to content
SAU Community

Recommended Posts

G-Day all,

Up for sale or Swaps is my Car.

Manufacturer: Nissan

Model: Skyline

Doors: 4

Date of Manufacture: 1990

Colour: Red Over Gray

Kilometers: 394,***Ks

Engine Size: 3 Litre Straight 6

VIN (Vehicle Identification Number): 6F4SCRR31K0J33

Engine Number: RB30160627A

Transmission: Automatic

Asking Price: $1500ono OR Swaps for something of interest.

The car is in Fair Cond for its age, it dose have a few dints and scrathes in it (see Pic) some area's of the paint isnt all that good but still have a shine to it the car has no rust that i could see.

Interior is in Immac, Just been Steam Cleaned and you can smeall the cleanness in it....... the dash has no cracks or any type of damage from the sun.

Engine and Box run fantastic, dose not miss a beat.... no noises or anythign from the engine, box or diff. i think the engine has been changed befor as it seems strong and the box shifts hard into gears would almost cherp.....

Wheels are stock and they need tyres.... (might try and get some Second hand ones for it)

Things i know of that need finxing:

Boot is locked down you need to climb into the boot from the back seat to open it.

Needs a new igniton Barrel... (iv got that)

Tyres.

Over all it is a nice car and would be great for a daliy bum around car or a project.

Contact Details:

Mob: 0420989267

PM Here

OR

E-Mail: [email protected]

Car is Located on the West Side of Vic, Werribee

Iv got a Vid Clip of it running and me walkin around the car.

Vid Clip

18062009243.jpg

18062009244.jpg

18062009245.jpg

18062009246.jpg

18062009247.jpg

18062009248.jpg

18062009249.jpg

18062009250.jpg

6-2.jpg

7-1.jpg

8.jpg

Cheers

------------------------------------------------------

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..   
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...