Jump to content
SAU Community

Recommended Posts

Hey guys I was wondering if you can help me out. I am in the process of finishing my engine off. I just put in a 25/30 and im connecting everything back up and getting it ready for its first start. HOWEVER. There is a nice thick black wire with a yellow stripe (just underneath all the wiring near the washer bottle) and I am wondering what exactly it does and where I need to connect it to. Im guessing it is the earth for the block but I'm not 100% sure and also not 100% sure about where exactly to put it. I have also just put in a Microtech LT12S.....(bag it out if you wish but its what I was recommended due to the tuners in Townsville....)..anyways. I have just put the ECU in and when I went to set the injector correction the hand controller didnt come on. So I had a look down at the ecu and it appears to have nooooooooooo power. Could this be from the mysterious black wire which I have no idea where it goes? All help is appreciated :rofl:

Cheers :D

Link to comment
https://www.sau.com.au/forums/topic/277236-ecu-has-no-power/
Share on other sites

Hey man, you are correct. The yellow and black wire is an earth strap and it bolts to the right of the engine mount. (not really important where you mount it as long as it is a good earth point on the block).

I dont however think this is your problem as the ECU would still get power regardless. Check over all your wiring into the Microtech and use a test light to make sure the ECU is getting power into all the pins it is supposed to.

Cheers guys I have today off so I will go work on the car some more and connect up that lead. If still no power I think I will just check the ecu harness. If anyone would know off the top of their head.......is the pin number for the main battery power supply to the ecu pin number 58?

Cheers

Ok I went and got a fuse box translation and pulled out the Engine Control 10A fuse to see if it was blown. Yes it was blown. I figured I could have accidently done something so I put the 10A fuse from the hazard lights in there. I connected the battery back up and turned the key. The hand controller for the ECUs screen light up and immediately turned off again. Disconnected the battery to check the fuse I just put in and it was f**ked too :( . OH O. Is the ECU drawing too much power or do I have a nice short circuit happening somewhere?

Cheers

Ok that problem is all fix now :banana: I just disconnected everything under the bonnet one thing at a time till it stopped blowing fuses. It was the connector for the igniter. I just took it off and pluged it in again and it seemed fine. Weird issue. Im on the clutch problems now. But thats for another thread. Thanks guys ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
    • Well this shows me the fuel pump relay is inside the base of the drivers A Pillar, and goes into the main power wire, and it connects to the ignition. The alarm is.... in the base of the drivers A Pillar. The issue is that I'm not getting 12v to the pump at ignition which tells me that relay isn't being triggered. AVS told me the immobiliser should be open until the ignition is active. So once ignition is active, the immobiliser relay should be telling that fuel pump relay to close which completes the circuit. But I'm not getting voltage at the relay in the rear triggered by the ECU, which leaves me back at the same assumption that that relay was never connected into the immobiliser. This is what I'm trying to verify, that my assumption is the most likely scenario and I'll go back to the alarm tech yet again that he needs to fix his work.      Here is the alarms wiring diagram, so my assumption is IM3A, IM3B, or both, aren't connected or improper. But this is all sealed up, with black wiring, and loomed  
    • Ceste, jak se mas Marek...sorry I only have english keyboard. Are you a fan of Poland's greatest band ever?   
×
×
  • Create New...