Jump to content
SAU Community

Recommended Posts

hey all. dad reversed my autech into the letter box the other day. ive gotten a quote for 750-800 ish to fix it. its the bottom drivers corner.. cracked the plastic. its going to have to be plastic welded back etc etc. i thaught rather than do that. maybe i could look at getting either a 2nd hand bar. or somthing eles. not sure i want to go viva... just coz its shit imo :yes:

Link to comment
https://www.sau.com.au/forums/topic/277671-what-rear-bar-to-get/
Share on other sites

Pics Adam...? Just got mine back from the repairers (Extensive Restorations in Lonsdale) after having the bumper squashed up after a tail ender and you wouldn't even tell it had been damaged - damn good job. Not sure if 260 bars are different from others - haven't really paid that much attention!

Edited by 32godzilla

If you go with another type you may have to modify the exhaust cutout in the bumper. I just fit a 260RS bumper to mine with an exhaust made for an RS-4 and the autech's hole is not only a lot bigger, but not centered in the same spot to give room for the stock exhaust.

It's not the best angle to show what I'm describing but you get the idea... muffler tip is at the outer edge of the cutout.

3680770245_5e619fe3ec_b.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...