Jump to content
SAU Community

Recommended Posts

Hey all puttin my 30det into my 32

okay so the cars a 92 gtst rb20det

head is a s1 rb25de

computer is a mapped rb20 to suit

question is-

can I run the rb20det loom? I've already put the rb20 cas and ignitor on so apparently it'll plug in?

Just want to be sure,have the s1 25 loom it had on it but it's been modified too many times,31>31>s13,

so don't wanna use it.

Worse case I get a 25 loom and wire it up,but why bother if the 20 loom will work on the 25de??

Thanks in advance,

Nathan

Link to comment
https://www.sau.com.au/forums/topic/280109-wiring-question-r32/
Share on other sites

rb20 silvertop loom will work for r32 rb25 non VVT head, providing you use standard injectors etc etc. Intake side sensor wise on both is the same, just your 25 intake ports are bigger on the head itself.

You have said rb25de s1 but, which still came in the R33 with VVT, this will not work.

The head must be a 25 non VVT from an r32, which I am guessing you have to dodge the vvt shit with the 30 bottom end.

Edited by James_03

it will work :blush:

my setup

R32 RB20DET

RB20DET loom, coilpacks, CAS, ignitor, knock sensors, afm, water temp sensor - all running off RB20 computer

RB25DE VCT S1 head, plenum, manifold, vct disabled. TPS, AAC, side feed RB25 injectors

other mods, 800cc injectors Z32afm HX35 turbo external wastegate.

everything runs perfectly, cuttently making 314rwkw and it drives like factory of the remapped RB20 ecu.

pm me if you need any help!

cheers!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...