Jump to content
SAU Community

++ B I G -- C L E A N O U T ++

nisskid
 Share

Recommended Posts

nisskid Grand Master

nisskid

Posted
Posted

Part are located near Mitcham in SA, can post anywhere in Aus at buyers expense.

Suspension/Steering

R32:

2x Front Sway Bar - $50ea

2x Front Camber Arms - $120pr -- PICS

2x Front Lower Control Arms - $150pr -- PICS

1x Front Tie Rod End - $10 -- PICS

2x Rear Lower Control Arms - $130pr -- PICS

2x Rear sway bar links w/ Urethane bushes - $30 -- PICS

2x Rear Hubs - $200pr -- PICS PICS

1x Rear Sway Bar - $50

2x Rear Toe Rods (non-hicas) - $100pr -- PICS

1x HICAS lock bar - $80 -- PICS

S13:

2x Rear Toe Rods (non-hicas) - $100pr

1x HICAS lock bar - $80

Misc

R32

1x Horn, can be hooked up to any car - $30 -- PICS

2x Stock Clutches, 1 half warn, one fair bit more warn - $50 and $100

1x Stock Rear Spoiler (with brake light) - $50 -- PICS

3x RB20 Coilpacks - $30ea

1x Turbo Timer, very basic timer, manual set - $20

1x RB20 Fuel Pump - $50 -- PICS

1x Igniter Module (breaks down under a lot of heat) - $30 -- PICS

1x Engine mount - $10 -- PICS

1x Airbox including snorkel - $30 -- PICSPICS

Random shit

1x Turbo Elbow - $30 -- PICS

1x Handbrake lever - $5 -- PICS

5x Hub Covers - $20 -- PICS

1x BBS Hub Cover Spanner - $10 -- PICS

Link to comment
https://www.sau.com.au/forums/topic/282436-b-i-g-c-l-e-a-n-o-u-t/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      Perhaps the answer is... more jacks!* *proper jacks must be used.  
    • GTSBoy
      Jacks that fit under GTR lips that can reach the subframe?

      By GTSBoy · Posted

      I NEVER think about using a scissor jack unless there is absolutely no other alternative. f**king things are dangerous, annoying and stupid.
    • PranK
      eBay "Hella" oil level sensor

      By PranK · Posted

      Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
×
×
  • Create New...