Jump to content
SAU Community

Recommended Posts

okies well i have a set of near new hsd tt's with around 1000km on them cost me $1399 from otomoto so they should still have warranty on them for 12 months.

and a set of tein HRs with the extra slave springs in them, the teins have one blown coil over from the rear so could do with some love and attention the other 3 are fine.

i am after $1500 for both sets pick up from brookvale can ship at buyers expense.

they are to suit a r33 skyline

prefer not to separate.

TT TYPE COILOVERS

The new TT type coilovers from HSD have been designed with every-day driving comfort as a priority. They use a twin-tube damper design (hence ‘TT’) which is less aggressive than the large-diameter mono-tube type dampers in the HR series. Spring rates are also generally 20-30% softer than the race-oriented HR series. In most cases the top mounting plate features a rubber bushing to reduce noise and harshness, but for strut replacements a camber-adjustable pillow-ball top is used for a larger range of camber adjustment.

Like the HR series the new TT uses an adjustable base bracket for easy height adjustment. The dampers also feature a 12-step adjuster for damping force. For a low-key appearance the aluminium lock rings and top plates are anodised grey, with black springs and brackets. The spring rates listed are our standard specifications. Alternative springs are available to order.

Link to comment
https://www.sau.com.au/forums/topic/282690-tein-hsd-coil-overs-to-go/
Share on other sites

the teins i am not to sure, they have the slave springs under the standard coil.

the hsd i think are 6kg nice for the street

hsds have done around 1000KM teins i am not to sure as they were in the car when i bought it but would not hurt for a service on them maybe.

i will get pics up tonight for you.

they are good quality and they have a nice smooth ride but i changed my plan for the car and am now after a firmer coil over for track / drift

people have said change springs but i want another set of bc's as i had therm in my last track day car and i have already done all the home work with them so it is easier for me.

and the teins came out of it when i did the hsd's so that is why i have them.

MIdnight_33 :

i will give ya $600 posted to vic

HAHAHAHAHAHAHAHAHAHA YOUR SO FUNNY YOU ARE LIKE OMG SO FUNNY 600 FOR BRAND NEW COIL OVER THAT COST ME 1300 JUST AVER A WEEK AGO HAHAHAHA OM MAN I HAVE A STITCH FROM LAUGHING SO HARD.

NO LOW BALL THANKS.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...