Jump to content
SAU Community

Rb26dett + Direct Port Nitrous Injection Setup

XRATED

By XRATED,
in Engines & Forced Induction

 Share

Recommended Posts

IMACUL8 Veteran

IMACUL8

Posted
Posted
11 hours ago, XRATED said:

...10 Years later.

XRATED is wearing a direct port set up on a greedy manifold. All WON gear.

 

J.

Pics of your engine bay now Justin please!

XRATED Veteran

XRATED

Posted
  • Author
Posted
9 hours ago, Dale FZ1 said:

So how's it go, and what issues needed sorting in the fitment and tuning of a system like this?

Importantly, would you do it again?

Really good ?

Do the research... or take it someone who really understands the application... not many folks fully understand this type of application in Aus.  Including a lot of people that tune.   Fitment will always be a compromise, unless you build the engine/car specifically for nitrous. Tuning... don't believe the o2sensor!

Well I keep doing it again and again and again on most of my cars, bikes and toys... so yes. Each set up is a bit different, to suit the application and as new tech becomes available.

 

Check out the WON forum to get started.

Setting up is like every other systems on your car, you get what you pay for... so don't cheap out.

If you have any qn's, pm me.

 

J

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Ahh. Well the block damage is a problem, you really need to run a tap or thread chaser through it to see if the threads can be saved, but any chips are likely to be bottom end bound which is bad. Earls seem to have what you need if you want to stick with mounting direct on the block: https://rceperformance.com.au/parts/earls-straight-adapter-1-8-npt-male-to-1-8-bspt-female.html, but as I said above I'd recommend remote mounting the sender
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm not quite understanding or I'm missing steps here, (I appreciate people are trying to inform my brain but I am of the dumb, especially today) - All I want to do is mount the male BSPT of the OEM sender into the system somewhere without it snapping the adapter via vibration. The Nissan sender has a male 1/8 BSPT output. The block has a (very destroyed) 1/8 NPT input. I'm not really sure how a lathe assists with that, and also don't know anybody with a lathe, nor specifically what I would want to buy. I'm not really sure how adding additional adapters creates a better, more leak proof resilient seal here.
×
×
  • Create New...