Jump to content
SAU Community

Recommended Posts

This is the solution to when your fuel gauge shows full all the time.

Thanks to MYGTST here is the soution to this problem:

"The fuel guage in the tank is a float type.

It falls off its mounting bracket quite easily. I found when mine did this all I had to do to fix this is to open the fuel tank from the boot and re-position the gauge.

Here's how to fix this, but before you do this it's an idea to have an almost empty tank of fuel and to remove the battery completely to avoid sparks as you will be opening the fuel tank.

Step1: Unscrew metal plate in boot on right hand side beside the strut tower.

Step2 : Unclip all wires leading into fueal tank but leave hoses attached (no need to remove them). EDIT - I found it easier to undo them.

Step3 : Unscrew the big plastic cap on the fuel tank be sure not to drop the rubber sealing ring into tank (plastic cap may need some gentle pressure to move). EDIT - This was extremly stiff on mine and I had to tap it off with a hammer and a chock of wood.

Step 4 : Reach into bottom of fuel tank and find your guage. EDIT - On mine it was an orange float facing the front of the car.

Step 5 : Just down and a little to the right of the fuel tank opening on the front wall is where the bracket is, bend the clip the gauge sits on a little to ensure it doesn't fall off again.

Step 6 : Make sure all wires are attached to gauge and clip into place and also make sure you cant unclip it (I used some large zip ties to secure the gauge in place to make sure it doesn't come off again)

Step 7 : Close fuel tank re-attatch all wires and put cover plate back on. Make sure tank is sealed and that you can no longer smell fuel vapours in the boot before re-installing the battery.

Step 8 : Start her up and go to the servo fill up about 20 - 30 litres and make sure gauge works.

All should be good now

DISCLAIMER : !!!!

I only recommend that people who are professional mechanics or who love to explode themselves and their car do this job.

You will inhale a lot of fuel vapours doing this, so work in a ventilated area and take regular breaks. The smallest spark will blow you and your car up so be careful."

Once again thanks to MYGTST and PVA_Glue for their help.

Please don't reply to this post, this is supposed to be a solution only. If anyone would like discuss it, please do so in my previous post.

Cheers,

Tim

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Can u check this way it works for power supply?
    • These coils draw 10amps that what i read online
    • I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
    • That worked out PERFECTLY! Thank you big time to JJ. He was able to swap me his stock diff. He drove all the way to me as well. Killer! Removal & install was pretty straightforward. The diff itself is HEAVY. So that’s a 2 man job.  Man does the car drive nice now! Couldn’t have worked out any better 👌
×
×
  • Create New...