Jump to content
SAU Community

Recommended Posts

Replacing just the seals or the entire injector set is quite an easy job. This work was done on an R32, but since the RB26 didnt change much over its lifetime the 33/34s are hopefully the same. All RB26s use the same injectors.

Note that if you change to a different injector size you MUST have programmable engine management.

WARNING: You will spill fuel during this work. I suggest you;

- Make sure there's no flames or sparks nearby, so no smoking (duh)

- Work on a cold motor

- Have a powder or foam fire extinguisher handy, and make sure you know how to use it (eg if there is a fire, first stop the fuel source, so dont forget to turn off the ignition to stop the fuel pump, then aim the extinguisher at the base of the fire - dont waste it by pushing the flames around). A hose can be dangerous in a fuel fire...

1. The day before you intend to do the work, thoroughly degrease and clean around the injectors.

2. Locate the fuel pump fuse, start the motor then pull the fuse. This will relieve the fuel rail pressure

med_gallery_15274_3433_124274.jpg

3. Remove the strut brace and cam breather hose

med_gallery_15274_3433_131577.jpg

4. Remove the three 5mm hex key bolts from the black plastic injector wiring cover (just for a bit more flexibility)

5. Disconnect TPS connector and the connector next to make some space

6. Remove the two bolts holding the fuel rail on, then gradually ease the fuel rail up and out. The injectors will probably come with the rail. You dont need to remove the fuel connections to the rail (which are tight)

med_gallery_15274_3433_121156.jpg

7. Ease the injectors out one at a time and try to catch any fuel with a rag. If replacing seals, remove the o ring from the top of injector and the rubber mount from the bottom of the injector or the cylinder head if it didnt come out with the injector. I used a watchmakers screwdriver to remove the o ring. If replacing injectors remove the metal clip from the electrical fitting, swap the injector and replace the clip. The outside of the o rings should be smeared with a little rubber grease.

med_gallery_15274_3433_17750.jpg

med_gallery_15274_3433_184625.jpg

med_gallery_15274_3433_34451.jpg

8. Once all the seals or injectors are done, mount the bottom of the injectors then line up the tops of the injectors with the rail and ease it on. Carefully press the rail onto the injectors. Install the rail mounting bolts finger tight then do them up evenly a few turns at a time each side so the rail isnt skewed as it goes on

9. Clean up any spilt fuel. Really. You'll start the motor soon and probably don't want to see it on fire.

10. Replace the wiring connectors, hex bolts and cam breather hose.

11. If you are installing injectors of a different size you need to update your ECU to cope with them.

- If using Nistune; turn the ignition on, load the config from the ECU, save a copy of the config to disk. Select 'Operations -> Resize Injectors'. Enter the original injector size and the new injector size. If the current injectors are OEM you can pull the size in with the 'Factory CC' button. If the new injectors have a different latency to the old ones, use 'Injector Latency -> Change Constant' to make the correction. Apply the new config to the ECU and save the new config to disk using a different filename.

- If using PFC; refer to: http://paulr33.skylinesaustralia.com/docs/...erfc-faq.htm#57

FWIW OEM GTR injectors have a latency of 770 micro seconds.

12. Start the motor, and watch for any fuel leaks. As the engine is cold it will be running open loop so if it doesnt idle well it probably means the injector re-sizing needs a tweak. Putting a smaller cc number or larger latency number in the resize option will make things run richer, and vice verca. For Nistune if you are changing the cc number remember to use the last figure you entered in the Current field - not the factory number. If you dont understand how cc and latency settings effects fuel delivery in different ways take it to a tuner.

13. Go for a short drive and re-check for fuel leaks

14. If you changed injectors verify AFRs are good with a wideband o2 sensor (all dynos have them). Light load driving is fine in the short term, as closed loop should compensate when the engines warm.

15. Reinstall strut brace and you're done!

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/285621-diy-gtr-injector-replacement/
Share on other sites

  • 4 months later...
  • 3 years later...

You will need the correct length 14mm injector with a 10.2mm adapter. If you try and fit injectors that are too long or short you will need to modify the rail spacers accordingly.

Also, the lower 14mm Oring needs to be replaced with a larger square section Oring.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...