Jump to content
SAU Community

Forged Rb30, Greddy Td06 Turbo Set Up & More

silver gts-t
 Share

Recommended Posts

silver gts-t Grand Master

silver gts-t

Posted
Posted (edited)

Selling my RB30 + Turbo set up

This was built by myself and dad (mechanic), block work done by Westend performance and tuning by Tom and BD4s

Engine has ran flawlessly for the past 4000km and a lot of good parts have gone into it..

Car ran in on 230rwkw and ran for about 1000km with 270rwkw with the small 8cm rear housing turbo

This will fall into an gtst with no issue.

Off the top of my head parts & work done:

Rb25de head (rare r32 head, no VCT)

Reco rb30 block (bore, hone, acid dip etc etc)

Reco rb30 crank (crack test, linish etc etc)

Cp pistons 9:1

Restrictors in block

Reco head

Gtr valve springs

Cpc custom plenum with billet throttle body (will come with acc cable to work in gtst also master cylinder to provide room)

Gates powergrip timing belt

New waterpump

Recondition oil pump

Crank shaft collar

Tomei cam gears

All new gaskets

Tomei head gasket

New tensioners

New king bearings, all replaced

Powder coated cam shaft covers with welded -10 bungs

Reco power steering pump

Hks fconV pro with map and air temp sensor

Gtr injectors

Price 5.5k

I'm sure there parts i've forgotten to list also

TD06 20g with 8cm read housing

Had this set up previously on my rb20 and made 260rwkw

anyone with it will tell you its one of the best rb20 set ups you can buy.

comes with:

recondition Td06 20g turbo 8cm rear housing

new front comp wheel

Front dump pipe

Oil line

Custom exhaust manifold

braided drain pipe

Tial 38mm Wastegate

Price $1.7k

If you want the turbo set up + motor i can provide a good price

extra parts i can sell to make the install easier are:

Custom power steering reservoir with lines and earls fittings

Custom radiator over flow bottle

Apexi pod filter

UAS catch can with light weight braided hose

rb20 gear box in good condition

Everything is in sydney and i prefer pick up..

Make an offer if you like but nothing stupid.

Thanks

John

Edited by silver gts-t
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • WMDC35
      Wheel Sizes & Offsets For Skylines

      By WMDC35 · Posted

      A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...