Jump to content
SAU Community

Recommended Posts

Selling my RB30 + Turbo set up

This was built by myself and dad (mechanic), block work done by Westend performance and tuning by Tom and BD4s

Engine has ran flawlessly for the past 4000km and a lot of good parts have gone into it..

Car ran in on 230rwkw and ran for about 1000km with 270rwkw with the small 8cm rear housing turbo

This will fall into an gtst with no issue.

Off the top of my head parts & work done:

Rb25de head (rare r32 head, no VCT)

Reco rb30 block (bore, hone, acid dip etc etc)

Reco rb30 crank (crack test, linish etc etc)

Cp pistons 9:1

Restrictors in block

Reco head

Gtr valve springs

Cpc custom plenum with billet throttle body (will come with acc cable to work in gtst also master cylinder to provide room)

Gates powergrip timing belt

New waterpump

Recondition oil pump

Crank shaft collar

Tomei cam gears

All new gaskets

Tomei head gasket

New tensioners

New king bearings, all replaced

Powder coated cam shaft covers with welded -10 bungs

Reco power steering pump

Hks fconV pro with map and air temp sensor

Gtr injectors

Price 5.5k

I'm sure there parts i've forgotten to list also

TD06 20g with 8cm read housing

Had this set up previously on my rb20 and made 260rwkw

anyone with it will tell you its one of the best rb20 set ups you can buy.

comes with:

recondition Td06 20g turbo 8cm rear housing

new front comp wheel

Front dump pipe

Oil line

Custom exhaust manifold

braided drain pipe

Tial 38mm Wastegate

Price $1.7k

If you want the turbo set up + motor i can provide a good price

extra parts i can sell to make the install easier are:

Custom power steering reservoir with lines and earls fittings

Custom radiator over flow bottle

Apexi pod filter

UAS catch can with light weight braided hose

rb20 gear box in good condition

Everything is in sydney and i prefer pick up..

Make an offer if you like but nothing stupid.

Thanks

John

Edited by silver gts-t
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
×
×
  • Create New...