Jump to content
SAU Community

Recommended Posts

Selling my RB30 + Turbo set up

This was built by myself and dad (mechanic), block work done by Westend performance and tuning by Tom and BD4s

Engine has ran flawlessly for the past 4000km and a lot of good parts have gone into it..

Car ran in on 230rwkw and ran for about 1000km with 270rwkw with the small 8cm rear housing turbo

This will fall into an gtst with no issue.

Off the top of my head parts & work done:

Rb25de head (rare r32 head, no VCT)

Reco rb30 block (bore, hone, acid dip etc etc)

Reco rb30 crank (crack test, linish etc etc)

Cp pistons 9:1

Restrictors in block

Reco head

Gtr valve springs

Cpc custom plenum with billet throttle body (will come with acc cable to work in gtst also master cylinder to provide room)

Gates powergrip timing belt

New waterpump

Recondition oil pump

Crank shaft collar

Tomei cam gears

All new gaskets

Tomei head gasket

New tensioners

New king bearings, all replaced

Powder coated cam shaft covers with welded -10 bungs

Reco power steering pump

Hks fconV pro with map and air temp sensor

Gtr injectors

Price 5.5k

I'm sure there parts i've forgotten to list also

TD06 20g with 8cm read housing

Had this set up previously on my rb20 and made 260rwkw

anyone with it will tell you its one of the best rb20 set ups you can buy.

comes with:

recondition Td06 20g turbo 8cm rear housing

new front comp wheel

Front dump pipe

Oil line

Custom exhaust manifold

braided drain pipe

Tial 38mm Wastegate

Price $1.7k

If you want the turbo set up + motor i can provide a good price

extra parts i can sell to make the install easier are:

Custom power steering reservoir with lines and earls fittings

Custom radiator over flow bottle

Apexi pod filter

UAS catch can with light weight braided hose

rb20 gear box in good condition

Everything is in sydney and i prefer pick up..

Make an offer if you like but nothing stupid.

Thanks

John

Edited by silver gts-t
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...