Jump to content
SAU Community

Recommended Posts

Kingsprings lowers (not superlows) came with the car (R34GTT) when I bought it 2 months ago and so far I've replaced a passengers side front last week and yesterday drivers side rear shocky, the front was fraked and the rear just leaking slightly but still working .

I have been advised by people who know that stock OE shockys should work fine with these springs as the lowering is only 20-25mm front and rear giving a ride hight of 360 front and 355 rear.

The car has 79500klm on it so lowering would not have made old shockys happy in any event.

I've replaced the shocks individualy as if they're going to keep blowing because the OE just aren't suitable I'll have to go for a different solution.

I'm just wondering if anyone else is running this Kings/OE set up and what thier results are ?

Edited by BASHO
Kingsprings lowers (not superlows) came with the car (R34GTT) when I bought it 2 months ago and so far I've replaced a passengers side front last week and yesterday drivers side rear shocky, the front was fraked and the rear just leaking slightly but still working .

I have been advised by people who know that stock OE shockys should work fine with these springs as the lowering is only 20-25mm front and rear giving a ride hight of 360 front and 355 rear.

The car has 79500klm on it so lowering would not have made old shockys happy in any event.

I've replaced the shocks individualy as if they're going to keep blowing because the OE just aren't suitable I'll have to go for a different solution.

I'm just wondering if anyone else is running this Kings/OE set up and what thier results are ?

mate never replace one shock at a time for starters very dangerous to thing too do that aside i run kings lowered springs not the superlows with a set of kyb shocks all round they have done about 20.000ks now and not a problem . thats on a r33 and it rides great the kyb's are a standed replacment shock to suit normal springs ive not had a prob

mate never replace one shock at a time for starters very dangerous to thing too do that aside i run kings lowered springs not the superlows with a set of kyb shocks all round they have done about 20.000ks now and not a problem . thats on a r33 and it rides great the kyb's are a standed replacment shock to suit normal springs ive not had a prob

Thanks for the reply mate , I'm puzzled about why only the only replace shockys in pairs, if that were the case shouldn't all be replaced when one goes ?

The replacements are factory and should be an exact match for whats in.

I was running around with one absolutely rooted (F) shocky for probably about 4 weeks and one partialy rooted ® for probably much longer and the only handling issue was a slightly harsh ride.

There were no hard braking aberations or steering/tracking/ handling issues evident , I will say though that I don't push the car around much. ah-hem :D

I only checked because of a slight noise at the passengers front side over very small very slow speed bumps.

I actualy talked with Jason at KYB and there are no fronts available in Aust for an R34GTT though they do make one,- part No NSF9092 gas adjust monotube, it will be available in NZ from georgestock.co.nz from the 29/10/09 (rears are FS9095 fork mount gas adjust monotube).

I'm quite happy with the OE damping just wondering if the OE is going to be happy with the Kings ?

Edited by BASHO

i have an r33 gtst. OE shocks with kings. haven't had any problems. i felt the ride was a bit soft, so i have just bought a set of TEIN HR coilovers.

some pictures

post-66323-1252462044_thumb.jpg

post-66323-1252462277_thumb.jpg

Edited by FAT 33

when i bought the r33 i had stock shocks and kings, 1 shock was nearly stuffed when i bought it, about 1,000kms later all were needing replacement, replaced with KYB's and haven't had a problem, driven about 10,000kms so far.

:) Thanks for the replys I guess I'll wait and see if either of the newy's blows if it does I'll get a full set of KYB's from NZ or go for coilys if a 2nd hand set turn up at the right price.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...