Jump to content
SAU Community

Recommended Posts

hey guys i'm not in a real rush to sell these but i'm putting them up just in case someone was willing to pay the money.

impul rs 17x9 +22 all round sprayed with super cheap gloss black paint.

235/45r17 wanlis in the front at 60% with abit of outer shoulder wear and 235/45r17 triangle talons in the rear at 70-80%.

they aren't in the best condition with a few gutter marks and being white originally and abit of paint flaking off but the black has covered all of that up. fit well on my r33 but considering my 33 isn't slammed. you might need to roll guards with 235 or be prepared to run stretch if your alot lower. most definately same thing for 32s.

will also swap for r32 gtr rims or stock r33 wheels with good roadworthy rubber with cash my way.

pick up in western suburbs in vic. prefer to sell locally.

$800

dsc00551s.jpg

dsc00549g.jpg

Edited by jakez88

damn nice wheels, if you were in sydney i would be interested.

what sort of price would you consider with out the tyres? $600?

jake i got r33 wheels 2 normal colour and really good tread other two are fluro green (can) and stuffed tyres... let me know

bang

Hi,

interested in your wheels and tyres.I am in Mordialloc 3195 where about are you in the western surburb? call me on 0439818008 to go further. can arrange stock r33 gtst wheels and new tyre to swap or purchase outright.

cheers

Alex

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...