Jump to content
SAU Community

Recommended Posts

Hi all,

I am looking at selling my FD or swap it for a vehicle of interest. I am in no rush to sell (possibly only an EOI at this stage unless there is genuine interest).

Make: Mazda

Year: 2000

Model: Rx7

Kms: 46,000

Here are the specs:

Freshly rebuilt engine (have receipts for over 8k of work)

PTS Seals

New Rotor Housings

Street Port

Brand new seals and springs

Current modifications are as follows:

Engine Modifications:

Greddy E-01 Boost Controller

SP Cooler (AVO production)

Re-Amemiya Air Filter

Re-Amemiya AST

FEED Cat-back Exhaust

SMB Midpipe

Custom front and dump pipe

Bosch 040 fuel pump

Sard Reg

Apexi Power FC

Twin Oil Coolers

Exedy Racing Button Clutch (3 Puck)

Koyo Radiator (uninstalled)

Suspension:

Tein Flex

Super Pro Off-set Upper Control Arm Bush kit

Brakes fitted with 700 degrees race pads

DBA slotted rotors

Wheels:

18x9 18x10 +35 Workmeisters

235 and 265 KU36s

Appearance:

FEED skirts

Re-Amemyia Diffuser

Ganador CF mirrors

Re-Amemiya CF Vortex Generators (not in Pic)

Interior:

Alpine Head unit with IPOD connector

Mazdaspeed CF gearknob

Fire extinguisher :P

No joy riders/dreamers ...

Price: $42,000 ono

Willing to separate parts if necessary i.e. wheels/suspension/modifications...

Plates: [FD3S] will not come with the car...

post-21334-1253221055_thumb.jpg

post-21334-1253221083_thumb.jpg

post-21334-1253221121_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/288482-fsswap-mazda-rx7-2000-fd3s/
Share on other sites

Nice, I didnt think you were really interested in selling it though?

Good luck, killer car.

I would sell it for the right price

Still got the GTR? :):P

  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...