Jump to content
SAU Community

Recommended Posts

Ok, today my dad and I installed the following:

1. Stillen Catback exhaust - twin tube flow design & stainless steel

2. Stillen front and rear sway bars

A lot of elbow grease, WD40 was required....

Pics of install:

Sway Bar - Front

aDSC00283.jpg

aDSC00284.jpg

aDSC00287.jpg

Sway bar - Rear

aDSC00266.jpg

aDSC00267.jpg

aDSC00269.jpg

aDSC00251.jpg

Exhaust - Old

aDSC00243.jpg

aDSC00241.jpg

aDSC00246.jpg

aDSC00248.jpg

aDSC00261.jpg

aDSC00249.jpg

Exhaust Comparisons - Old vs New

aDSC00255.jpg

aDSC00257.jpg

aDSC00262.jpg

Exhaust - New

aDSC00274.jpg

aDSC00275.jpg

aDSC00276.jpg

aDSC00277.jpg

aDSC00281.jpg

aDSC00280.jpg

Final Product...

aDSC00288.jpg

aDSC00289.jpg

aDSC00290.jpg

aDSC00291.jpg

aDSC00292.jpg

Commentary:

1. despite the pricey amount (and super expensive shipping), I would happily pay to buy the Stillen exhaust again. It gives a slightly deeper drone at idle and is just as quiet as the OEM unit.

2. At full acceleration, the noise is not loud (unlike the many previous exhaust I have had on my other cars over the years)

3. The car feels more revvy and feels more powerful at full acceleration. Stillen claims it adds an additional 21 to 23 HPs...Obviously, I need to get it on a dyno if I wanted to prove it...

4. If you ask how come I didnt get a JDM exhaust, let me tell you a secret....Stillen are class leading when it comes to their products on Nissan 350z, G35s, Altimas....

Ok, after all that, I was going to install the Stillen front Strut Brace - but here's the problem....I have killed my strut tower nuts x 3 whilst trying to undo them. Can anyone suggest how I can get them removed??? They are the 3 nuts on the battery side where there ain't alot of room to move...

Link to comment
https://www.sau.com.au/forums/topic/288782-my-stillen-exhaust-sway-bars/
Share on other sites

Nice work! Looks like your dad was doing all the work while you were taking photos :)

I've got the same Stillen strut brace and same problem as you have (strut tower nuts on the battery side). I will wait until my next scheduled service and get my mechanic to fit it.

The Stillen twin tips stick out a tad too much don't u think? Someones gonna trip over them one day or even worse get burnt lol.

2. use a hammer and a chisel to turn them

i have used both methods

yeah I had to do that when I rounded the nut holding my front strutbrace

had to take my car off the ramps, jack up the front and take the wheel off for more clearance, hammered the side of the nut so it kind of had an edge again and then chisel with mallet the little f^cker finally popped loose

think the chisel and hammer might be a bit awkward on the strut tower bolts as they kind of sit horizontal as opposed to vertical when I did my swaybars. def give the vicegrips a go, otherwise suck it up and get a local mechanic to take it off for you :ninja:

Nismo - I did a lot of the work also, it's just that there was no way for my dad to take pics of me under the car...

We tried the vice grip pliers for like 20 mins, but not enough clearance to get it to bit and turn (except for an upwards position - meaning no turning force)...

We tried WD40 for 1 hr...

We tried hammer and chisel for one of the nuts, and it was like butter...didn't do sh*t...

We tried hammering a Size 11 socket into it (was a size 12 nut)...no luck there and rounded the nut further...

I am so annoyed now..can't concentrate on anything, just thinking about those 3 bugger of nuts....

Yo-yo - yes, front sway bar nut was also a killer...took 20 mins per nut to undo...the secret is getting enough ground clearance to maximise the elbow/arm force...

RS73 will be taking a sound clip when I see him next....

so file two opposite sides of the nut to make them flat, then use a shifting spanner on them! easy!

also, all you need is leverage to undo tight bolts, buy a breaker bar, then put your trolley jack handle on the end of it if its not long enough. you dont need to get the car all that high up.

  • 4 weeks later...

Finally found a nut remover tool kit...wasn't cheap and set me back $120....

If you are after one of theses kits, don't bother going to Bunnings or the Auto Shops....You can only get them at the professional tool shops.

The nuts came off so easily with this tool....credits to the inventor!!!! It's such a simple design...might take a pic of it to show u guys wat the fuss is all about...

So today, it will be off to buy some replacement nuts, and put in my Stillen strut brace!!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
×
×
  • Create New...