Jump to content
SAU Community

Recommended Posts

Item: WTB RB25DET Chipped ECU

Location: anywhere will pay for postage cost

Website: here & other

Item Condition: good & working with no faults at all

Reason for Selling: your selling

Price and Payment Conditions: you tell me

Extra Info: WTB RB25DET Chipped ECU, good & working with no faults at all

Pictures: yeah pm me

Contact Details: reply here or pm

Link to comment
https://www.sau.com.au/forums/topic/290432-wtb-rb25det-chipped-ecu/
Share on other sites

i have a chip for a series 1 rb25det. tis only the chip not the whole ecu.

was in a r32 ecu and only reason it was taken out was to get remap.

i pulled 240rwkw on 15psi with this chip and 32 ecu wiring combo.

i have a chip for a series 1 rb25det. tis only the chip not the whole ecu.

was in a r32 ecu and only reason it was taken out was to get remap.

i pulled 240rwkw on 15psi with this chip and 32 ecu wiring combo.

i got s2 25 mate so its prob no good for me...

any idea where i can buy them from?

go and get your car remapped.

depending on where you are depends on price.

you will need a 32 ecu or you can find ppl that will remap a 33 ecu but they are big $$$

either that or its a power fc for u

  • 2 weeks later...
  • 2 weeks later...

well its a simple guess.PFC plus tuning. looking at 2k plus.

33 ecu remap looking at 1k if they even know what they are doin. you might be able to pull off a r32 remap for about 500 including buying the ecu and the remap costs. just seen a r32 ecu sell for a stupidly cheap $50. keep looking and you will find.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...