Jump to content
SAU Community

Recommended Posts

Make: nissan skyline

Model: 1993

Milage: 195,000k's

Transmission: manual

Colour: maroon/burgundy

Location: central coast NSW

Complied? yes

Currently registered? rego till feb 10

Price: $8,000 ono, all reasonable offers considered

Contact: 0424 143 184 or email me at [email protected]

Comments / Modifications:

General

Factory Type M bodykit (Front bar, side skirts and rear pods)

Nismo clear side indicators

Nismo leather gear knob

R32 GTR wheels (16 x 8 +30 lightweight forged aluminium)

Power

Kakimoto HyperMega Dual N1 Catback exhaust (dual 2.5" pipes from the cat into dual 4" cannons)

BOS Importing (Batmbl) Split dump/front pipe

Catco stainless core 5 inch body high flow cat

ARC R34 SMIC

Remapped ECU by Toshi (no speed limit, no rich and retard, optimised A/F ratios and timing)

FET Coil packs

Turbotech boost controller

Nismo fuel pump

Drivetrain

Nismo GMAX Twin plate clutch and flywheel

Short shift kit

Handling

Full Sydneykid suspension package -

Bilstein dampers with adjustable height circlips

Whiteline Springs

Whiteline adjustable swaybars

Whiteline adjustable camber & castor bushes

Whiteline pineapples

Whiteline dust covers and bump stops

Genuine GTR rear strut brace

JJR Front strut brace with brake cylinder brace

Hicas lockbar

Stopping

DBA 4000 slotted rotors

Winmax 0-600 degree pads

Electrics

Earthing kit

Remote central locking, alarm and dual immobilizer

Images:

RIMG0054.jpg

RIMG0058.jpg

RIMG0061-1.jpg

RIMG0062-1.jpg

these photo's were taken just after i clayed and waxed it.

ill throw in a set of 19's aswell, engine is starting to use a bit of oil probly due to the amount of k's on the car, other than that she's sweet, still pulls as hard as the day i got it.

make an offer

Link to comment
https://www.sau.com.au/forums/topic/291573-nsw-1993-skyline/
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...