Jump to content
SAU Community

Recommended Posts

Hi all,

Can someone please confirm if the side skirts and the rear pod bits on the car in the picture are a nismo body kit?

If so, does anyone know how much they are worth new? And how much they have roughly been selling for when used / second hand?

Any info is much appreciated.

Cheers!

post-54322-1255524277_thumb.jpgpost-54322-1255524322_thumb.jpg

Edited by KR4-GTR
Link to comment
https://www.sau.com.au/forums/topic/292035-r34-gtr-is-this-a-nismo-body-kit/
Share on other sites

Hey Chris,

Genuine Nismo gear is very expensive.

Side Skirts $1270 via air or $1100 via sea, Price do not include local GST or import duties.

Rear pods $860 via air or $840 via sea, Price do not include local GST or import duties.

Cheers,

Johno

Hey mate, they look like the Z-tune side skirts and rear pods.

I just bought a set of the skirts and pods from Bodyform Aero in NSW for $580 ($330 sides/$250 rear)

From all accounts I'd heard, Bodyform were the way to go so I took the plunge and gave them a try.

Peter and Allan there were very helpful and quick to respond to emails.

I've written more on here about my experience with them.

http://www.skylinesaustralia.com/forums/in...t&p=4850400

My car is currently in getting them put on, I'll be picking it up after work today so I can provide pics of what it looks like but I'm pretty confident it'll look good.

When I dropped the parts in to DT Panels, their reaction was "Whoa are these genuine? Are you sure?? They look very well made!" haha that brough a smile to my face.

They're either genuine Nismo or Nismo lookalike. Most replicas seem to be made with fibreglass, the real ones are plastic. The side skirts make the car bloody low, I've already had a few decent hits on speed humps, and when I saw the price on replacing them, I decided to get them repaired instead lol

Uh oh haha, I knew it would make it lower but was hoping it wouldn't be too much lower!

Have you lowered your car too Kristian? I'm hoping I can survive my driveway when I get my car back tonight.. the front lip gets a good bashing already at home and I had to take it off!

Yep agree, there is no way mine is driving over a coke can either, unless the can is on its side maybe :whistling:

if it can go over a coke can on its side... its still to high... flat coke can FTW!

Mine are F/G from JSAI. They were as I recall, about $700 for both sideskirts and rear pods.

I had my front splitter body-colour-coded at the same time (but that's on a car which is already black).

Bodyform Aero makes/fits the same. E: [email protected] P: (02)87835446

I was originally going to say that, lol

By the way, Animal Chin is at my place

hahaha.. "i have a friend, his name is animal, dont worry bout his name, he's not a cannibal, he's always happy, he's got a grin... have you seen him..

he's Animal ch-ch-ch-chin!"

ill be there sunday so we'll find him... is johnny rad there too?? dont want to miss his gig... you guys are gelling.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...