Jump to content
SAU Community

Os Giken Tripple Plate Clutch, Tomei Fuel Rail

blur

By blur,
in Classifieds

 Share

Recommended Posts

blur Proficient

blur

Posted
Posted

I have a OS Giken tripple plate clutch assembly for sale (flywheel, plates, throwout bearing). It is in good condition, seems to have plenty of friction left.

Was removed as its too harsh for my application. The throwout bearing will need to be replaced but I have it as its a smaller diameter to the nissan one to make it easier to match up. Its a push type, so will work on early model (upto 92??) without modification, laters will need to be converted over.

I can email pics. Located in Brisbane, prefer local pickup as it is quite heavy and would be expensive to post, but will at your expense.

Chasing $900 obo

Also have a Tomei fuel rail. Blue anodised, comes with screw on fittings for dash 6 hose only. Its in as new condition, infact i dont think it has been used, certainly doesnt have any petrol smells or scratches around the bolt holes.

Looking for $200

Bride Zeta 3 seat no rail never used. Genuine seat, come with my car but doesnt really suit me. Its the frp version with the fia approved sticker. Black and grey

$reasonable offers

Please pm or leave an email and ill respond as quickly as possible.

  • 3 weeks later...
blur Proficient

blur

Posted
  • Author
Posted
pm me mate pretty keen on clutch how much meat goin 2 a gtst so as long as it holds up for awhile i might get it

Sent a PM a few days ago, did you receive it?

Any offers, pretty keen to sell this stuff!

blur Proficient

blur

Posted
  • Author
Posted

Clutch sold to dahandful

Pics uploaded of tomei rail. Dont have any of the seat yet, but it really is as new for anyone whos looking.

post-1208-1260878422_thumb.jpg

post-1208-1260878490_thumb.jpg

 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...