Jump to content
SAU Community

Recommended Posts

hi people as tittle states i am looking at selling my engine set up due to wanting to go turbo v8 now.... the motor has only just done 120km and is still running in.... make me an offer if you are a geniune buyer please..... owes me over $30,000. dont be affraid to make an offer only if you have the money.

ALL OFFERS CONSIDERED

(rb25/30)

prept rb30 block

nitrided crank

dowls removed from crank

acl race bearings mains, big ends

crank collar with grub screw

n1 oil pump

new water pump

spool h-beams rods

arp 2000 rod bolts

wiesco custom 25/30 pistons 7.8-1

total seal gapless rings

cometic head gasket

rb25 head convertion

performance valve springs 65 pound

adjustable cam gears

keford billet cams 272deg 9mm lift (intake/exhaust) non vct

porting and pollishing intake and exhaust (12 hours)

1mm over sized stainless intake/ exhaust valves

arp head bolts

strut brace

ROSS RACING harmonic balancer

cometic inlet gasket

cometic exhaust gasket

gcg exhaust manifold t3 flanged

tial 38mm waste gate

screamer pipe

garrett t04z with t3 flange rear housing for faster spool

custom front mount and piping

tial blow off valve

3" exhaust

custom MR ENFORCER plenum with trumpets

xf throttle body

haltech e11v2

eboost 2

individual coil packs

billet fuel rail twin -6 entries with a -8 return

seimen 870cc injectors

turbosmart fpr2000 fuel regulator with gauge

competition black 100gph carter pump

2x044 700hp pumps

twin outlet 4ltr surge tank

braided fuel lines

nos fogger system 75hp shot

turbo bag

pwr alloy radiator

1000cfm thermo fan

jim berry custom clutch 4400pounds 4 puk solid center

r33 gear box

oil filter relocation kit

+ heaps more

bigger turbo setup:

6 boost manifold

billet t72q turbo

heat shield

progate 45mm waste gate

4" inlet with pod

4" dump pipe

the car made 488rwhp with standard head and ran 10.82sec 1/4, with 1.51sec 60ft, car lost traction at last quarter of track due to line coming off and sprayed oil on tyres and still did the time......

new engine ant turbo setup will make close to 600rwhp on pump, and over 700rwhp on c16 with more boost..... no money spared on the motor.....

kirk 0410757949

P1000360.jpg

P1000362.jpg

P1000363.jpg;)

Edited by grunter01
Link to comment
https://www.sau.com.au/forums/topic/294626-big-hp-rb2530/
Share on other sites

yeah it was, and still is at the moment

may consider parting the setup if i get people wanting most of the parts.....

Mate I saw what you are asking for on CT.

Its a f%cking bargain. I am surprised it hasnt been snatched up already.

GL with sale anyway mate.

Link to comment
https://www.sau.com.au/forums/topic/294626-big-hp-rb2530/#findComment-4920198
Share on other sites

  • 2 weeks later...
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...