Jump to content
SAU Community

Recommended Posts

I have a Honda CRX for sale. I've lost interest in finishing it.

Location Jerrabomberra NSW/Canberra ACT.

Built DEC 91

KMS 241XXX

New Springs

New tyres

New indicaters front and front side.

$4500 ONO or may consider swap.

Email [email protected] or call 0408513746

Link to comment
https://www.sau.com.au/forums/topic/294640-honda-crx/
Share on other sites

  • 2 months later...
  • 2 weeks later...
  • 4 weeks later...
  • 3 weeks later...
Currently getting roadworthy and engineered. Who would consider buying it for $5k with rego?

Considering I got a 98 Civic in near mint condition, 103K odo for $5,500. Nope. I was considering a CRX originally but Civic was too similar for a much better price and condition.

Wish you luck.

Link to comment
https://www.sau.com.au/forums/topic/294640-honda-crx/#findComment-5105561
Share on other sites

  • 4 weeks later...

First the rims are 17x7inch and it only comes out with 5 inch wide rims. Its normally 1.5inches bigger but the same year civic came out with 5.5inch rims

Second cannon exhaust on the rear

Third aftermarket steering wheel

And Forth POD filer

Link to comment
https://www.sau.com.au/forums/topic/294640-honda-crx/#findComment-5141248
Share on other sites

  • 2 months later...
  • 2 weeks later...
  • 1 month later...
  • 2 weeks later...
  • 1 month later...
  • 3 weeks later...
  • 3 weeks later...
  • 1 month later...

Gotten lotta scam emails also while trying to sell my Pulsar. Still want it sold and gone.

Aftermarket steering, pod and exhaust don't need any engineering certs.. They are perfectly legal - well in ACT, can't vouch for NSW, prob does need certs there... As for the rims, just put it through pits on stock rims *shrugs*

Sorry you are having no luck selling, I've had no word bout my car either, even with price drops. But mine is complete all work done, 100% working condition and nobody has any interest in it... had a couple calls in the past month, that was it. Just the wrong time of year to be selling and market is a bit dead atm.

Link to comment
https://www.sau.com.au/forums/topic/294640-honda-crx/#findComment-5578122
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...