Jump to content
SAU Community

Recommended Posts

So my mate has a R33 RB25det manual.

Mods include 3inch cat back and turbo timer. Standard boost without going through the solonoid (7psi?).

Everything else its stock mechanical wise.

He rang me today and said once he got of the m7 doing the 100km/h speed limit when he back off in gear, very loud pops can be heard.

So I intially thought it might have been the normal popping sometimes associated with a bigger exhaust.

These are loud crisp pops and sound to be in sync. I mean pop...pop...pop... not pop......popopopop.........pop. Sort of thing.

Also now when starting the car it will stall unless the pedal is held for 5 seconds and then the car gains idle to 800-950rpm.

No check light has come on yet. Checked all vacuum lines, not leaks and everything seems to be in good working order visually.

Any thoughts?

Link to comment
https://www.sau.com.au/forums/topic/294703-r33-problem-after-highway-driving/
Share on other sites

mine is similar except mine doesnt stall and the pops aren't in 'sync'.... when i get off the gas say at 6-7000rpm and revs drop to about 4000 it makes a loud pop + flame then a few little pops... i think its just the big exhaust (3inch straight through into 4inch muffler) + mine is running a tad bit rich hence the flamage..

edit: car is a series 2 r33

Edited by defari

Yeh this is deffinately not the over rich sound poping.

If you drive in 2nd @ 60 and back off the whole way on deacel its pops the same loudness like. Same sort of pop noise and its crisp not a rich sounding pop pop.

Check fuel pump and lines. if you gotta feed it to get the revs back so it doesn't die, and it's backfiring (usually a sound associated with not getting fuel - bare in mind it IS an rb25det with standard computer), then it sounds to be a fuel issue. fuel pump, lines, AFM could also be outta whack.

Backfire is generally excess fuel getting into the exhaust and being ignited by the heat. Since the injectors shut down at full decell, it must be a leaking injector feeding fuel during decell. Get the injectors cleaned.

It may also be that the injectors are not shutting down, and that is usually a result of the TPS getting out of whack and not sending the "throttle closed" signal to the ECU. Check the TPS for 0 ohms at "throttle closed".

OK quick ecutalk scan showed:

tps: .12v @ idle, 4.3v 100% throttle

afm: 1.2v @ idle - forgot 100%

02 is deffinatley stuffed. it sometimes adjusts from .20 to .40 but mainly sits on .00

Would the ecu see this as lean or would it ignore if tps and afm read full throttle.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah agreed, you can't assume that shop are they only people who ever had to work on it. It was just a guess on the mods based on how things were done back then. You can check the Air Flow Meters by the part number on their tags, they are likely either Z32 or Nismo ones (both read about the same but the Z32 one is a little larger while nismo is stock size but supports the higher airflow like a Z32). And yes, all that would get you to 450hp / 340kw To tell what is happening with the turbos, you want a photo of the tag on the core, that will say what it was made out of  (they can retain the front and rear covers to make the plumbing easier)  
    • I'm selling my personal race car. 1992 BNR32 Skyline GT-R About eight years ago the engine developed the dreaded low oil pressure problem. I removed it and found the issue. However shortly after I moved half way across the country, moved my work shop, bought a house, got married, then moved my shop again to it's permanent location for the time being. in turn I do not have the time to race this car as it should be. In turn the engine I built for this car will end up in my street car and this car I hope finds a home with someone who can use it to it's full potential. The roll bar was built by Jason Noren Fabricaiton in Pomona California to SCCA and NASA Specs. The car used to compete in redline time attack and global time attack enthusiast class. It also has a fire suppression system.  The car is with me at my workshop in Kyle Texas, USA. Shipping it is no problem, I can personally deliver the car to the port of either Houston or Los Angeles. Any other port depending on where it is may require transport but we can always work that out.   The chassis itself is rust free, rear quarters and under fenders are free of any rust so it's a very solid foundation for anyone who wishes to move forward with it. As posted and at the asking price of $20,000 USD the car includes all of the following;   All OEM Body panels, front fenders, rear bumpers etc.  OEM Nissan Projector headlamps (Pictured N1 lamps were removed) OEM Nismo Side Skirts / Extensions OEM Rear Spats  Front & Rear Subframes are installed car is full roller Rear Subframe has Cusco Camber Arms, Whiteline HICAS Elimination Front Subframe has Whiteline tension rods and whiteline Sway bars w/ endlinks.  Buddy Club N1 Coilovers All chassis wiring and engine wiring is in tact. Attessa System is fully in tact and was functional before engine removal.  BCNR33 GT-R Brembo Brakes F+R with Endless MX72 Plus Pads, DBA Rotors & Stainless Steel Brake lines Billion Racing Radiator Billion Radiator Hoses Fluidyne Engine Oil Cooler Accusump System (trunk Mounted) 5 Speed Transmission w/ Transfer Case F+R Prop-shafts Rear Differential With rear Axles.  Nismo Gauge Cluster Nismo Clutch + Flywheel   Essentially what is needed to make this car running and driving again is as follows: A working Engine, an ECU, and time to put it together. The price posted is or best offer as I am willing to remove some components to accommodate price to a certain extent. If any serious buyer wants full detailed pictures, videos, or any questions I'll be happy to answer them. I believe this car is priced to move quickly considering it's a rust free and very straight chassis but always open to fair negotiation.  I can be contacted via phone or email. (+19517081648) email is [email protected]   
    • So...to my (and my mechanics doing the swap) surprise...the oil pan from NEO engine does not fit 100% and needs to by modified like this: It is not a huge problem but in the future i want a "proper" oil pan. So question is...what different oil pan can i get to fit without any problems and modification? Thanks! 
    • Some more info I found.  These are the last entries Yoshikiyo Fujii made on his blog before he passed away in 2009: http://blog.livedoor.jp/fujii_dynamics/ And finally this is where the workshop was situated:  https://maps.app.goo.gl/HhTPtHzt3WVcBTiEA  
    • shit boxes, kids, and daily drivers are all welcome
×
×
  • Create New...