Jump to content
SAU Community

Recommended Posts

OK, Just had the ole' RB26 rebuilt and now these parts have to go. Postage is available on some items and the rest are pick up only from Homebush in Sydney.

Item 1: Stock R33 GTR turbos. They have done 94000kms. When the GTR came over from japan it was compression tested and the results were 272 in all cylinders! No shaft play at all. These turbos have never seen a hard day in thier life. - $500ono. Pickup only.

post-16592-1257683538_thumb.jpg

post-16592-1257683573_thumb.jpg

post-16592-1257683608_thumb.jpg

post-16592-1257683637_thumb.jpg

Item 2: Greddy Profec E-01 Boost controller. High/low and overtake boost control modes with manual control or full auto. Boost data logging capability up to 3 hours. Great condition. - $400. Can post at buyer's expense.

post-16592-1257684428_thumb.jpg

post-16592-1257684456_thumb.jpg

post-16592-1257684478_thumb.jpg

Item 3: Stock RB26 cam shafts, PC - $200. Pickup only.

Item 4: Stock RB26 injectors, PC - $300 the lot with rings. Can post at buyer's expense.

Item 5: Near new Nissan R33 GTR clutch fitted by Prince Oita in Japan just before shipping. Did about 4000kms in Australia before being replaced with a OS Giken STR Twin Plate. Great OEM replacement item. - $150. Pickup only.

Send a PM if more info is needed.

Link to comment
https://www.sau.com.au/forums/topic/295434-rb26-parts-for-sale/
Share on other sites

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
×
×
  • Create New...