Jump to content
SAU Community

Recommended Posts

Hey all, some of you might know me from this site, some might not. Either way, I've had my skyline for 9 months or so, and my journey has been interesting. I've learnt a LOT along the way, about RB's, and about cars in general. I thought I'd share my story of dealing with Tuff Toys.

So around December 08 - Jan 09 I started looking for a car. I had a falcon at the time and wanted something japanese and turbo! Test drove a couple of 180s and silvia's, drooled over an S15 or two but they were plain out of my price range. A couple of months before this, my workmate and I noticed Tuff Toys moved into Virginia, next to All Jap... we both drove past it each day on the way to work and always talked about how much we both wanted a sick car from there... hahaha.

Went in and spoke to them, told them what I was after and they were happy to help me out, let me test drive one of their 180s I had my eye on, and were always happy to have a chat and answer any questions I had - and I had a lot hahahaha.

Their cars were a bit out of my price range, fair enough.

I ended up finding my 33 at another car yard at Motorscene at Albion, simply because it was cheap. Had a friend look it over and I was sold.

Over the next couple of months I took my car to Tuff Toys to replace/upgrade a few basic things:

  • Oil, fluids, and filter change straight away
  • I had them take out the coilovers that were in there and replace with stock shocks and kings low springs
  • Brake pads/rotors
  • All 3 of my 3 month/5000km services so far (could do them myself but I need it done by a shop for my warranty)

They've also helped me out with figuring out weird noises (boost leak from BOV gasket) and helped me reconnect my turbo timer when its wires came loose in the dash because I was fiddling in there (!). They taught me about my manual boost controller and told me how to connect it/reconnect it (I wanted to DIY it to learn how it worked at the time), as well as helped me out with a multitude of noobish questions from me and have always been more than happy to help me out without charging for stuff like that.

They've never stuffed me around, and I've never been surprised at the cost. If anything 'bigger' had to be done, they've let me know and told me how serious it is and how long until I'd need to do it - which is EXACTLY what I want in a mechanic. If you need anything mechanical done, I'd have no problem recommending them to the skyline community. Wayne knows his skylines and has realistic expectations from them.

Anyway, my two cents. Cheers.

Edited by mosquitocoils
Link to comment
https://www.sau.com.au/forums/topic/296802-tuff-toys-importersmechanic/
Share on other sites

Hahahahaha yeah.... to be honest I HATED the coilovers. Waaaayy too stiff for street use which is all it will see while in my possession, other than the odd drag soon.

  • 8 months later...

Somehow they got me on their mailing list and used to email me every week with new cars they had.

I haven't heard from them in about a year or so and there's no website for them.

I'm not sure what's next to justjap now though?

Hey guys PM me if you want the mobile number for them... they've moved out of Just Japs property and moving over to the southside from memory

Tufftoys arranged compliance for my Skyline personal import from japan and were very helpful , I cant compalin about anything.

Moved to

Shed 2 / 298 New Cleveland Road

Tingalpa Qld 4173

Phone: (07) 3390-4277

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...