Jump to content
SAU Community

Recommended Posts

Hi all i have my fishing boat up for sale.

It never gets used so needs a good home.

It is a 3.2 metre fibreglass boat with 2 seats, side trays, front storage area.

it comes with oars and rollicks as pictured.

my father (a fibreglasser/boat builder) and I built this boat and we put extra reinforcement in the transom to enable it to carry a motor up to around 5hp.

I ran it with a 3.3hp and it never had a problem and due to its weight was quite fast across the water

Note. motor not included in sale..

Its reasonably light and can be put ontop of a ute/4wd or a trailer by two people no dramas.

The boat is in excellent condition and only has a few minor chips and scratches on the hull from general use.

Come on people dont let it go to waste. Get yourself a Great Fishing boat for use over the summer. :)

SPECIFICS.....

ITEM : 3.2m Fibreglass Boat

Condition: Great

Reason for sale: doesnt get used and needs a good home

Price: $500 ono.

Location: Central Coast NSW

Contact: post up here for any more details or Pm me on here if genuinly interested and ill give out my mobile number.

post-27646-1258629375_thumb.jpg

post-27646-1258629400_thumb.jpg

post-27646-1258629441_thumb.jpg

post-27646-1258629482_thumb.jpg

post-27646-1258629507_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/296962-fibreglass-dinghy/
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Swapped the injectors around and the misfire followed. I went ahead and ordered the Deatschwerks 550cc injectors and am currently waiting for them to be ship and arrive. In the meantime, I've had my Nistune soldered to the ECU. Tested it, and and tried it out with the software. Everything should be prepared for when the injectors arrive.  
    • Yeah they charge a little extra for mods , last year I noted no mods but I did have an exhaust fitted after that so  better to let them know cause these kinds of things can cause the policy to be void if you ever need to claim.
    • Hello, just just bought an 1999 enr34 with a stock rb25neo and I'm looking to upgrade the engine to 500whp I know some basic things but wondering if there are things I'll need to do to upgrade the stock block and all the bits and pieces to achieve this.
    • Thanks everyone for the replies and suggestions. Got the seats out (hoping I could find some existing grommets but no such luck). By tapping and measuring etc. I could figure out where I could drill through if needed. But first I borrowed an inspection camera and managed to go through factory holes in the chassis rail and could see that the captive nut was holding steady which is why it could retighten. So it was indeed a stripped section of thread, so I applied downforce by levering the bolt head with a screwdriver and went slowly back and forth until it came out. Camera helped a lot cos I could monitor that the captive nut was holding tight. Now I just have one very seized main subframe nut to tackle 😅
    • BOVs do have a purpose, if you ever log pressure before and after the throttle body, you will see a spike pre throttle on lift off from a WOT condition. Enough to bend throttle blades / damage e-throttle motors or simple assist in blowing off cooler pipes. FWIW, the above on really applies to those running at least 2 bar of boost. OP shouldn't have an issue, on the other hand, here are some videos of my shit box over a decade ago with some succulent dose with the airbox on and off. That shit box is unrecognisable these days 🫠    
×
×
  • Create New...