Jump to content
SAU Community

Recommended Posts

selling RB26 block only, no sump no head no water/oil pump.

this is block, pistons, rods, crank and bearings only, all assembled ready to go :D

specs are

Block:

Line honed

o-ringed

sonic tested

hot tanked

stress plated

bore honed

blue printed

Crank:

cross drilled and plugs fitted

linished

balanced

Aries pistons 20thou oversized

Crower rods

ARP main studs

traveled roughly 20,000kms

asking $6000ono

block is in Melbourne and available to view most days after 4pm

cheers.

Link to comment
https://www.sau.com.au/forums/topic/297092-rb26-forged-and-built-block-only/
Share on other sites

price drop $5500

guys if your looking at doing this yourself its probably gonna cost in excess of 7grand dont waste your time or your trouble its all done for you ;) might be a nice early chrissy present too hehe

Price is good I can vouch for this engine (block) .

p.s mine is already built ready to go

cheers for the vouching :huh:

and good to hear its all ready to go...... when will i have the pleasure of seeing this beauty then hey?????? hopefuly soon :D

  • 2 weeks later...
  • 2 weeks later...
price drop $5500

guys if your looking at doing this yourself its probably gonna cost in excess of 7grand dont waste your time or your trouble its all done for you :) might be a nice early chrissy present too hehe

just a quick question, is the block 20,000k's old, and all work just carried out, or 20,000k's since work was completed on it???

if it is 20,000k's old, how did you treat it? how much power was it making, and what oil pump were you using?

it was 20,000 since the work was carried out, it was still the original block. how did i treat it?? umm well i looked after it like i said always serviced and taken care of, you need to understand that those 20,000 were done over nearly 3 an half years, the motor was assembled in march 06. it was making just over 400kw at the wheels towards the end of this year but has always been on a safe tune, and i was using a Trust oil pump

  • 4 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...