Jump to content
SAU Community

Recommended Posts

bit of a list:

S2 full interior (front+rear) good condition $300

radiator support panel $250 (tell me where you want it cut)

Ignition barrel + driver door barrel + key $100

S2 dash (with passenger airbag & panel) $250

Auto Gearbox with stage 2 shift kit $500 (unknown condition, apparently works fine)

GTR Boot lid wtih hinges (No Wing) $100

S2 Steering wheel with airbag $300

rear tail lights pair $200

centre garnish (white) $50

rear corner windows $50ea

stock suspention set $200

Seatbelts, full set $100

Instrument cluster $120

White R33 fuel cap $50

Standard Rb25 BOV $50

rear view mirror $50

Auto tail shaft $150

steering rack $180

back bumper $100

rear window $100

driver door with glass and motor $150

diff $80

Centre console (no handbrake boot cover) $50

hood lining $50

carpet $100

rear sway bar $50

driver mirror $50

Electric antenna $50

A/c control gc $120

drivers side Blinker on the guard, indicator switch on the steering column, surround on the window switch on the drivers side door

drivers side blinker as in the whole indicator?

r33 indicator stalk $50

surround i have has carbon fibre vinyl on it $40

Hey mate do you have the plastic bit that fits under the car stereo ? (Skyline R33) http://www.skylinesaustralia.com/forums/po...26-IMGP0142.JPG (example) put the keys and stuff in it... im in Melbourne if you have it might need to post it out or something.

Edited by DarkRyda
whats the boot trim like?

well its not in the car , but its all excellent condition , just gotta work out how many pieces go with it, also have the piece of wood that goes over the spare, im pretty sure its all complete

  • 5 months later...

should actually keep this up to date hey ...

steering wheels gone

parts left over :

auto gearbox

front glass

rear glass

1/4 glass

drivers side window

drivers side door with lock

ignition barrol with key

hicas unit with toe arms

hubs

knuckles

front uprights

boot with lock

abs unit

  • 2 weeks later...

hey mate, how much for the front knuckles, are they in good knick? mine have a fair bit of play and not sure how regency will like that. I have no idea what they are worth.

hey mate, how much for the front knuckles, are they in good knick? mine have a fair bit of play and not sure how regency will like that. I have no idea what they are worth.

they are still on the car at the moment but im pulling them off tonight

last i checked they arent cracked or anything

$100 for both with uprights

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...