Jump to content
SAU Community

Recommended Posts

Agreed - very cool - have been meaning to try it sometime but haven't yet.

There are two ways to do it - the proper way (as gadl above does)

and the cheating way where you take one pic and do it in PS in 3 steps

(obviously not as good!)

Here for example is one I made the cheating way (pretty crap)

before

2009_02_05%20Brisbane%20CBD.jpg

after

2009_02_05%20Brisbane%20CBD%20Land.jpg

Link to comment
https://www.sau.com.au/forums/topic/297679-wee-planets/#findComment-4954920
Share on other sites

1. Convert the photo into a square image

Use the Photo|Image Size menu item to change the image size into a large square. Uncheck ‘Constrain Proporties’ and set the “height” value to the same value as your “width” value.

2. Turn image upside down

Rotate by 180°

3. Apply the polar effect

“Filter|Distort|Polar Coordinates” filter - choose the “Rectangular to Polar” setting

When selecting a photo to start with you should keep the following things in mind:

  • Select a panorama photo or a cropped landscape photo (aspect ratio at least 2:1, which means the width should be at least two times the height).
  • The bottom area (bottom 25% or so) of the photo in most cases should have only very little detail (e.g. sand, asphalt, water). This area will later be in the middle of the picture and will also be distorted the most.
  • The upper area (upper 25%) should also have only little detail, most preferably just one color (e.g. blue sky, night sky etc.).
  • The left and the right border of the photo should neatly fit into each other (which is always the case for a stitched 360° panorama).
  • The horizon must be exactly horizontal, the left and right end of the photo will be joined together and if they are on different heights your planet will have a big crack in the surface (again this is no issue for 360° panoramas).
Link to comment
https://www.sau.com.au/forums/topic/297679-wee-planets/#findComment-4955114
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
    • Probably. I take it that they are also mentioned to be for R34 Skyline? For example.... RDA has that part as RDA7957. I have the dimpled and slotted version of that on my car https://www.ebay.com.au/itm/285518478694?srsltid=AfmBOopKxMuAFpsxZJdB1cam4D5RAj1f9yJyOttPZLAwXVNCOiwlhrIy This is DBA's top one piece equivalent https://www.ebay.com.au/itm/364246686631?srsltid=AfmBOorbb0XHQgqTvZLgQPhg70nqJtGvdojKnugum3O2LFSr2h-obp8D  
×
×
  • Create New...