Jump to content
SAU Community

Recommended Posts

I got an S-AFC soon after getting my mildly modded car (T04 turbo, exhaust, boost controller, small FMIC) and it gave me a uniform extra 15rwkw across the board.

Then after a few more mods, which were a bigger FMIC, new front facing plenum, bigger fuel pump, upgraded wastegate actuator to handle more boost, and running higher boost, the car got 2 massive dips in the powerband even after re-tuning the S-AFC. I had more power up top, but it felt very flat after 5000rpm or so.

At this stage I upgraded to a PowerFC and it's fixed it. And I haven't even tuned it yet. I don't think it was a case of the ECU and S-AFC not handling the power, I just think the airflow was so radically different from stock that caused it to have a bit of a sad. There are other guys running over 215rwkw with S-AFC and no problems. Part of it is luck.

I say you should get a second hand S-AFC, and when the car starts not coping, sell it and get a PowerFC.

I know PowerFC is defectable in SA but is the SAFC?

are you serious?

how can the defect u for a PFC

coppers rip off ur kick panel and go "show me ur ECU"?????

its gettin beyond a joke this defect bullsh*t

Oh another question, with cam gears do you need a aftermarket ecu to run after market cam gears?

You don't need an aftermarket ECU to run adjustable cam gears but it may help. I installed mine and I found that the best setting was on 0 degrees (ie same as factory). This may change after tuning though.

You can't easily tune them yourself at home, best to do on the dyno where you can monitor the air fuel ratio so you don't run it too lean. If you know how to use a dyno properly it should take around an hour, otherwise give it to the workshop and they'll charge you around $200-300 for the same thing.

2GU UP

I am dead serious, the cops don't pull off the kick panel.

But the Registration office that does the inspections for defects will pull your car apart looking for stuff like this.

I have even heard of inspectors undoing the casing to look at the circuitry on the ECU to check that it is standard. You would have to be desperately unlucky I would imagine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
    • On the bright side, the weather will turn much nicer for working outside shortly....sounds like you might need to start on a neighbour's garden next
    • Ok so i will NEED to have this sensor anyway even with Nistune (or standalone ECU) https://justjap.com/products/genuine-nissan-boost-pressure-sensor-evap-control-system-fits-nissan-r34-skyline-c34-nm35-stagea-pnt30-x-trail-rb25det-vq25det-sr20vet?currency=AUD&srsltid=AfmBOoqfxX48bW9bEwH62orcNhtBfp7ekAL0C9Ca89ySFGUiBzXfXeze Is this the correct one? And this is only thing i need? No other "things" connected to the sensor or something? I do have the wiring.
×
×
  • Create New...