Jump to content
SAU Community

R33 Steering Noise When Turning

koduRB25det

By koduRB25det,
in General Maintenance

 Share

Recommended Posts

Mayuri Krab Grand Master

Mayuri Krab

Posted
Posted
they all good.

do u know the reson for rev up while i turn the steering...?

Does the revs go up everytime u turn the wheel or only does it when you turn the wheel while the car is stationary?

If its the latter, my car does that as well.

shyr33 Community Regular

shyr33

Posted
Posted

Ye I think that is normal, don't quote me but when you are at low revs e.g. idle then want to turn the wheels it takes a bit of power from the power steering pump etc so I think it compensates for that by increasing the revs in order for it not to stall. But im just throwing up ideas.

mosquitocoils Veteran

mosquitocoils

Posted
Posted

I knew I'd read about this before, pretty sure it's normal. Check the link and look at the highlighted bits near the top.

http://www.skylinesaustralia.com/forums/Di...teering%2C+blip

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      eBay "Hella" oil level sensor

      By PranK · Posted

      Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...