Jump to content
SAU Community

R33 Rb25det Build. Safe Mode Cut At 2500-3000rpm, Running Rich.


Recommended Posts

Hey Everyone,

Ive been building my rb25det r33 series 2 over the last 12 months or so.

I have it to the stage where it is ready to be registered etc. And have had it running.

However, it looks like it is in safe mode and very possibly the AFM is not working.

Has anyone got any sure fire ways of testing the AFM to see if it is in fact broken or do I need to find someone with a working AFM and hook it up to test it out?

I have checked ohms across all three points on the AFM and none of them read '0' so I am assuming that somewhere inside it is failing at resisting .

Some info. The 02 sensor is a brand new bosch replacement. So this should be working 100% (unless my wiring fails, which Id like to think I wired it correctly). The AFM seems to be the culprit.

Any thoughts from anyone? Or anyone living near Petrie north Brisbane with a spare series 2 AFM we could throw on it to test.

Cheers,

Trent

try and borrow (or buy) a consult cable. this way you can plug a laptop into the car and see if there are any error codes and check the AFM voltage at the ecu.

as for o2 sensor, it won't make any difference to how it runs. i ran my car for a few months without it being plugged in.

  • 4 weeks later...

Hey Everyone,

Still having issues here.

Ive got the consult and tested everything over and over again.

It appears that the previous owner of my loom had a safc in it.... not such a huge issue.. traced everything back etc. all good.

The Afm is putting out a voltage signal of around 2.7volts without the engine running. Is this normal?

When the engine is turned over. the air being sucked through cools it to around 2.3volts.

The engine itself wont start while the afm is plugged in. The pulse width on the injectors stays at around 0.8 etc. and the ecu still spits out error code 12 for the afm circuit.

When i disconnect the afm it starts up again in safe mode. injector pulse goes back to normal etc. still with the same error code.

This is a series 2 ecu, loom with pink sticker afm.

Thoughts anyone?

2.7V is very high for not having the engine running. i think they should be around 1.5V at idle if i remember correctly and 0v if the engine isn't running. it could be a faulty AFM or a wiring issue (such as faulty earth)

Hmm sounds to me like a dodgy AFM. If it starts and idles mint without the AFM plugged in id say that would be the case.

Itd be wise to see if some nice person will let you borrow one.

I know a dude that bought a 2nd hand AFM, same problem, then bought a OEM Nissan brand new for $600... same problem. Was a faulty earth in the ECU. I tried to lend him mine, but he was confident it was the AFM haha,

  • 4 months later...

Hey guys

I have the exact same problem, but what do you mean by a faulty earth in the ecu?

Are you talking about the ecu external casing being grounded to the body of the car or is it something else, can anyone please advice as im loosing the plot over this :banana:

Cheers James

  • 2 months later...

faulty ecu earth could be a number of things.. most of the earths collect in a small brown plug near the ecu where they are bridged together, as well as the 4 or 5 pins in the ecu that are earths.

Obviously the ecu has power and so is earthed but it may be the sensor wiring is damaged or misconnected ie wrong wire, or even one of the switches on the board is not operating or has burnt out in which case a new ecu is probably in order.

I vaguely remember with the power fc hand controller i had the afm off the inlet pipe but still connected and i was blowing through it watching it go from 0 to 0.34v or something like that. get someone to watch the pc and see if it changes when you blow through.

I have also had some interesting issues with running different series gtst afm's on cars, maybe you should look at the plug end, especially if thats ever been changed. A series 2 afm for example on a series 1 you need to leave one of the 2 sensor earths disconnected.

thanks for sharing your experience jeffworld2, i just recently cleaned my AFM with contact / circut board cleaner, it was absoluely filthy... it was amazing if it could measure anything, stupid HKS pod filter filters nothing. car seems to be running a bit better, although i did notice the idle rpm seems to be a bit higher.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
×
×
  • Create New...