Jump to content
SAU Community

Recommended Posts

once again, these are up for sale. got hella interest. but no ones fronted the cash (most promising offer would make most lowballers cringe).

work mesh, 17x8 +5 and 17x9 +11. fronts are straight 5x114, rears are multifit 4/5x114.

bit of kerbage on them, but you have to be looking pretty close. the worst of them was one of the 9's which had a slight dent in the outer hoop which has recently been repaired.

and some of the clearcoat is starting to peel around the hubs, but overall, theyre in pretty rad condition.

4902P5120746.jpg

IMG_3157.jpg

taking offers around $1500 without tyres. offers lower than $1400 will be laughed at, and responded to in kind.

contact me (dave) on here or on 0408961657.

can send interstate if needed, but id rather not.

if you dont shit me off within 4 seconds, i might even be able to arrange a payment plan.

Link to comment
https://www.sau.com.au/forums/topic/300557-sa-17-inch-work-mesh-wheels/
Share on other sites

  • 2 weeks later...
ugh, bump again. gotta be some interest out there.

What rubber is on them ? Brand/sizes ? Just to get this right........ +5 multi stud on rear ? SO +11 BEING THE 9" and larger width wheel,

is on front ? Cheers MIKE

i got interest in the bump photo bro :rofl: haha what other wheels you bought?

lol, f**kin rad bump pic eh?

havent bought wheels yet. but im looking at cts's, 17 x 9.5 +15 all round.

What rubber is on them ? Brand/sizes ? Just to get this right........ +5 multi stud on rear ? SO +11 BEING THE 9" and larger width wheel,

is on front ? Cheers MIKE

225/45/17 Kumho Ku36's on the front (f**kin sticky), and 215/45/17 Kumho Ku25's on the rear.

the fronts are 17x8 +5, rears are multistud's and 17x9 +11.

ive had about a half a dozen people say that, and my reply has been the following.

im not splitting. you either buy all 4, or you dont buy them at all.

ive had about a half a dozen people say that, and my reply has been the following.

im not splitting. you either buy all 4, or you dont buy them at all.

Why not say, sure, for $1500 and I'll chuck in two fronts for zip!

:banana:

If I had $1500 blowing a hole in my pocket I'd snap em up (too bad I'm post-wedding broke ATM)

lol then if you wont split, you never gonna sell these wheels, well njot at that price, i just bought a full set that had just been re rolled and polished with tires for $900...

Why not say, sure, for $1500 and I'll chuck in two fronts for zip!

lol, ive said that once aswell.

lol then if you wont split, you never gonna sell these wheels, well njot at that price, i just bought a full set that had just been re rolled and polished with tires for $900...

CoolStoryBro.jpg

lol then if you wont split, you never gonna sell these wheels, well njot at that price, i just bought a full set that had just been re rolled and polished with tires for $900...

sounds like your polishing more than your wheels there frenchy

bump to the top for some tough,well priced rims and tyres

deposit received.

lol then if you wont split, you never gonna sell these wheels, well njot at that price, i just bought a full set that had just been re rolled and polished with tires for $900...

... you were saying?

:D

  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...