Jump to content
SAU Community

Fs: A31 Nismo Strut Brace

D4NM4C
 Share

Recommended Posts

Nic_A31 Grand Master

Nic_A31

Posted
Posted

How does it not fit your S13?

A31 strut towers are the same as S13 (formation the the top, distance from one tower to other)....the only difference is the A31 has less height clearance, so in all cases, A31 braces will fit S13, since most S13 braces fit the A31 depending on how high up they come.

Sure it's not for something else ?

D4NM4C Rookie

D4NM4C

Posted
  • Author
Posted
How does it not fit your S13?

A31 strut towers are the same as S13 (formation the the top, distance from one tower to other)....the only difference is the A31 has less height clearance, so in all cases, A31 braces will fit S13, since most S13 braces fit the A31 depending on how high up they come.

Sure it's not for something else ?

The distance between the strut towers is fine and so is the clearance for the engine, the issue is the firewall is closer on the S13 and hence the BMC sits next to the strut tower, whereas in an A31 it's placed further back

D4NM4C Rookie

D4NM4C

Posted
  • Author
Posted
Did you try putting the strut brace on the other way, so the bar would be on the other side of the struts?

Also, what is your location?

Yes, putting it the reverse way the bonnet doesn't close

I'm in the ACT

  • 3 weeks later...
RBceffy25 Rising Star

RBceffy25

Posted
Posted

As far as my own personal research has shown, cefiro front strut barce an sway bar are unique and will only fit cefiro.

For strut brace i use UltraRacing and for sway bar Selby.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • codygrimm27
      Can you mount the ATTESA pump in other locations?

      By codygrimm27 · Posted

      Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      You think its the AFM? I know its a common issues on R32s. I find it coincidental how this issue raised right after cleaning the fuel system. As everything except the fuel system was fine before. I tried running it with the IACV unplugged but did not notice a difference and still stalled. However, the RPM gauge is not in the cluster right now, so I will need to connect the laptop again and use Nistune to check the RPM. I will check this weekend.
×
×
  • Create New...