Jump to content
SAU Community

Fs: R34 Gtr Wheels, Hqs Ssqv Bov, Apexi Power Intake Filter


Recommended Posts

Hello all,

I am in the Hills, Sydney NSW.

FOR SALE:

One set of R34 GTR wheels, no tyres. I picked these up years ago and never bothered getting rubber for them. Condition of rims is just as I picked them up. Rims are in a good condition, a few nicks and chips here and there, and one has very very light gutter scuff which has been lightly resprayed (check photo). Centre caps in excellent condition included.

$1700 pickup only

post-41614-1263294440_thumb.jpg post-41614-1263294681_thumb.jpg post-41614-1263294786_thumb.jpg post-41614-1263294924_thumb.jpg post-41614-1263295009_thumb.jpg

One HKS SSQV BOV. Used for about 5000kms, excellent condition. I still have the original box!!! Is advertised for fitting HCR32 & HNR32 but fitted my er34 no problems

$300 pickup or buyer pays for postage.

post-41614-1263295234_thumb.jpg post-41614-1263295491_thumb.jpg post-41614-1263295671_thumb.jpg

post-41614-1263295806_thumb.jpg

One Apexi Power intake filter. Used for about 15000kms, good condition.

$40 pickup or buyer pays for postage.

post-41614-1263295902_thumb.jpg post-41614-1263296091_thumb.jpg

I also have the following stock parts for er34 (r34 gtt):

Stock Front/dump pipe + stock cat $50

Stock springs and shocks $50

Stock er34 SMIC $80

Feel free to PM me to come check out any of the parts for sale. :P

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • And yes would be going to tomei Japan for sure as it’s closer to me … 
    • Yeah I heard the same. Might be hard to order one. But then I guess can go to hks or go to a more expensive n1 block with tomei. Guess will jump the hurdle once I get there next upgrade around. I can’t get work done in the states as the lead time will take for ever on top of shipping to Hong Kong. 
    • https://www.platinumracingproducts.com/en-us/products/nissan-rb26-cast-blocks This is the solution I was thinking of. I would stay away from Tomei USA, their quality is a question mark to me. If you want an engine machined in the US contact Club DSPORT: https://clubdsport.com/ Tomei JP is probably fine but I recall they stopped doing pre-assembled short or long blocks. In general it's pretty tough to get any kind of RB26 block at the moment with Nissan so severely backordered.
    • PAR specifically offers stock ratios in their gearset and you could do whatever ratios are physically possible supposedly for no extra cost. I agree 6 ratios is better than 5, the factory 2nd gear is equivalent to the Getrag 2nd gear if you account for the differing final drive ratio though. The Getrag 3rd gear with a 3.916 final drive is equivalent to a 1.6 2nd gear in the FS5R30A. I'm about to swap the transmission out on my car, I'm tempted to send the one I have now out for rebuild with the standard "cross ratio" gearsets out there to see if it really makes such a big difference the next time I pull the transmission.
    • This is what I was looking at next:  https://www.z1motorsports.com/engines/tomei/tomei-rb26-28l-short-block-assemblies-p-45479.html as we can’t bore the cylinders out in hk so better just buy the whole lot in one and install then retune. Everyone saying the weak link are the bolts holding the rods together. I already did valve springs, arp head bolts, hks racing coils, nismo fuel pumps and pressure regulators, injectors etc for the top of the engine. 
×
×
  • Create New...