Jump to content
SAU Community

Recommended Posts

has a couple of creases on the roof from where the old bonnet blew up a while ago. got quoted $220 to fix it good off the dingo dents guy. i never got it done coz it doesnt bother me too much. was going to but didnt

price: $13000 will swap for cars, bikes, boats. jetskis, hookez

selling my r33. current rb25 motor has low compression on 6th cylinder. its down to 50 psi or so.

- registered until 4th month sometime

have a rb30 rebuilt bottomend with

- new mahle pistons and rings

- crank collar

- new king bearings

- hole drilled for 2nd tensioner to put twincam head on

- grub screwed crank

- bored 1mm oversize

- ready to put rb25 head on

and have a rb25det head all rebuilt. fair bit was done to rebuild it like new. has had the welding mods done and new vct fitting attached ready to put on rb30 block. tapped threads to put the rear oil drain in.

- have new nissan headgasket

- new nissan headbolts

- bottomend gasket kit

- top end gasket kit

parts on car

- exeedy ceramic button clutch that slips when you cain it. replacement clutch plate is $250 delivered but the car comes with a good new clutch

- blow off valve

- 3 inch exhaust

- 17 inch wheels (not that good but)

- all tyres are good

- 400r bodykit with standard front bar

- 5 speed manual

- cd player

- front mount intercooler

- front facing plenum

- probably few more things but its just the basic upgrades

parts that come with the car

- new motor setup

- npc bigmouth track clutch rated to 400kw

- new billet flywheel

- greedy copy plenum kit (plenum-80mm throttle body,fuel rail)

- spool imports head rear oil drain kit

- proboost 38mm wastegate

- highmount stainless turbo manifold

- wolf 3d v4 plugin ecu

- will update any other bits i have

car blows fair bit of smoke after boosting. thought it was turbo seal but after doing a compression test id say its from the low compression piston. made 250rwhp couple of months ago with the problem. its got fair bit of good stuff to make it good. just needs to all be put in

selling the car with all the parts as a package. just needs few other parts like turbo and injectors and itl hamma. can get a proboost to4z turbo for about $800. did have one but sold it. was aiming to make 450rwhp with all this stuff.

- located on northside of brisbane

- pm me if your keen

r33skyline019.th.jpg

r33skyline011.th.jpg

r33skyline012.th.jpg

r33skyline015.th.jpg

r33skyline005.th.jpg

r33skyline014.th.jpg

r33skyline013.th.jpg

r33skyline009.th.jpg

r33skyline016.th.jpg

r33skyline017.th.jpg

r33skyline018.th.jpg

r33skyline008.th.jpg

r33skyline006.th.jpg

r33skyline007.th.jpg

carparts008.th.jpg

carparts016.th.jpg

carparts007c.th.jpg

carparts019.th.jpg

carparts004.th.jpg

carparts021.th.jpg

carparts017.th.jpg

carparts020.th.jpg

carparts013.th.jpg

carparts009.th.jpg

carparts012.th.jpg

carparts005.th.jpg

carparts015.th.jpg

carparts018.th.jpg

carparts011.th.jpg

Link to comment
https://www.sau.com.au/forums/topic/303655-r33-2-door-skyline-400r-bodykit/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...