Jump to content
SAU Community

$ Value Of Genuine Gibson Motorsport Rb20det

31GUN

By 31GUN,
in General Automotive Discussion

 Share

Recommended Posts

twins Explorer

twins

Posted
Posted

going back to that exhaust manifold. some might not think its worth $9k... and it probably isnt really. but where else could you get someone to make a single piece manifold like that with that level of craftsmanship and quality? i would say that maybe half that cost would be the most i would pay but then it comes back to the whole thing where it is a one off item. unfortunately that means that there is no real way to value this and its up to hooks and any potential buyers to work out what this is worth to them because this isnt going to pop up again any time soon.

  • Replies 89
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

esky_mad Proficient

esky_mad

Posted
Posted

a few years ago i worked for a company called DHS, they design and make the stretches etc for NSW ambulances as well as build the ambulances on site.

my point being.. there was so much development that went into making jigs for parts that your average joe blog would never pay any attention to. and this development isnt cheap, for what looks like a bunch of plates, bolts and nuts bolted together (albeit a very nice bunch of plates bolts and nuts) was well over 10k... i'd happily believe 9k was invested in developing the original GMS manifold.

i could go on but im hoping most here are educated enough to know where those costs go..

the key word here being "development" its never cheap, regardless of the whats trying to be achieved.

on topic, i would happily hand over a large sum of cash for an original GMS motor, they sound incredible, and it would fit nicely into my cefiro

....infact id prefer it over a 26 and defnitely over a 25..

NZM.031 Grand Master

NZM.031

Posted
Posted
@ R31Gun......Pretty sure that was Linton's way of get a response to Ash from me......you know those kids that used to stand behind the big kids in kindergarden shit stirring so they can get a fight started......same sort of thing......but some of us grew out of it!

yes it was... im a smart arse, im sorry for trying to keep this thread somewhat light hearted.

@Linton....didn't know there were sides....shit this sounds like I'm back at pre school.....I am also with Ash and others on some of what they say....shit even you!.....and I don't care how long I have know them.....nor do I really care if they know me or not.

no there are no sides... and it didnt matter who knew who, r31gun made that comment like it was important

Just to straighten things out....as you seem to have dropped a couple of silly misplaced comments in. e.g. Pin drop(I did smirk and mumble to myself shit stirrer though), weddings.....

im glad that you saw them as silly comments as thats all they are.

If you want to go and stir people into response's go then get some ball's and go the whole hog e.g. Tell you wife/girlfriend that she's got a fat arse while she's in the middle of her PMS cycle. :) ......make sure you video it for posting on youtube or Police evidence(Oh....not having a go a your wife/GF either as I have never seen her)

nooooooo bingo.... are you mad??

I have been an Industrial Designer on a CAD for 15 years and at no time have I ever been able to do or see someone else rack up a part design similar to the exhaust we are talking about in 30 minutes.....not even a day.....not to mention my hourly cost which I can tell you now is not cheap! I am sure HKS can make em.....how much though? For a one off?

is that your hourly rate that you get paid?? or the hourly rate your company charges you out at??

Wedding's and cars have nothing in common other than most of us will loose our cars as soon as the wedding happens......P.S. maybe you should not type you thoughts in future.

*insert thought here*

The $200(or has it now gone up to $1,500) of metal you have estimated may be correct.....but the hours your going to put into em is where the cost is......are you going to garrentee these will be able to glow red for six's hours without falling apart. If you are you should be working for a major motor sporting team as you are in short supply. Also I will want your details for future reference just incase our main set which has probably done more race hours than any other Group A in the world since 1988 get damaged (Yes thats right not fall apart get damaged).

it remains at around $200... i enquired about 4m of 2mm thick stainless pipe yesterday and it was around the $300 mark

Jetwreck Grand Master

Jetwreck

Posted
Posted

Glad someone else is as scared as his woman as I am!

I nearly posted this last night.....now that you have done it

Crank up the volume for a lap with an RB20....I never get sick of this sound.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      OK, so a bunch of trim needs to come off to get to the rear shock top mounts. Once the seat is out of the way, the plastic trim needs to come off. Remove 2 clips at the top then slide the trim towards the centre of the car to clear the lower clip Next you need to be able to lift the parcel shelf, which means you need to remove the mid dark trim around the door, and then the upper light trim above the parcel shelf. The mid trim has a clip in the middle to remove first, then lift the lowest trim off the top of the mid trim (unclips). At the top there is a hidden clip on the inner side to release first by pulling inwards, then the main clip releases by pulling the top towards the front of the car. The door seal comes off with the trim, just put them aside. The the lighter upper trim, this is easy to break to top clips so take it carefully. There is a hidden clip towards the bottom and another in the middle to release first by pulling inwards. Once they are out, there are 3 clips along the rear windscreen side of the panel that are hard to get under. This is what the rear of the panel looks like to assist:
×
×
  • Create New...