Jump to content
SAU Community

Recommended Posts

hey guys,

I'm new at this and I need find out whats needed to be done, on a 100,000km service.

I'm planning on changing the oils-

Flushing engine

Coolant

Front and Rear Diff

Spark plugs (leaving for the pros)

Timing belt (been done 89,000km ago)

Gear box

Air Filter (Buying Apexi intake)

I'm a noob but i need start somewhere.

This going be my first time changing any oil, so please help me.

I need know where unplug the oils and change them.

To learn I need get my hands dirty.

I may sound like an idiot that knows nothing, but I'm will to learn to improve my knowledge.

Thank a lot guys

Amon

Link to comment
https://www.sau.com.au/forums/topic/305032-100000km-service-on-r32-gtr/
Share on other sites

what do you mean the timing belt was done 89,000kms ago? you mean it had it done at 11,000kms? or are you meaning it was done at 89,000kms?

also if this is your first time changing the oil i don't know if you should takle the timing belt by yourself. it isn't super hard to do, but there is a possibility you could destroy your engine if you do it wrong.

and what do you mean you are leaving the spark plugs to the pros?

as for the actual method for doing any of this, there would be a write up on pretty much everything you are planning on doing if you search the DIY section

what do you mean the timing belt was done 89,000kms ago? you mean it had it done at 11,000kms? or are you meaning it was done at 89,000kms?

also if this is your first time changing the oil i don't know if you should takle the timing belt by yourself. it isn't super hard to do, but there is a possibility you could destroy your engine if you do it wrong.

and what do you mean you are leaving the spark plugs to the pros?

as for the actual method for doing any of this, there would be a write up on pretty much everything you are planning on doing if you search the DIY section

Hey mate,

Thank for the info, well the timing belt was done at 89,000km's and with the spark-plug I'm leaving it to the mechanic.

I'm not going to even touch the timing belt, as I know that if been done wrong, can do some damage or even destroy the engine.

I'll give the DIY section a look.

Thx

Amon

oh ok. if the timing belt was done at 89,000km it doesn't really need to be done, but then it comes down to how long ago it was done. just make sure that the tensioner pulleys, etc are done at the same time.

the engine oil is pretty straight foward to do. just make sure the car is warm when you do it.

for the diff and gearbox oils, make sure you can loosen the filler holes before you even bother touching the drain holes. if you can't get the filler holes undone then don't drop the oil as you won't be able to fill them back up. the gearbox isn't quite so bad as you can put it in through the gearstick hole (if it is anything like the 2wd gearboxes).

I'm pretty sure the tensioner pulleys were done. When I purchase my vehicle they said it was done and i had the engine checked by my mechanic and he said all good.

As for the engine oil i hope its easy to do. but for the diff and gearbox oils, got no idea what to do and what kind of method is involved.

Thx

Amon

Hey mate,

Not sure if you've already started doing the service but I did my 100k service about 2 weeks ago so while it's fresh in my mind I thought I would make a list for ya.....

1. Replaced water pump with new factory item (Done by tuner)

2. Replaced timing belt (Done by tuner - don't attempt this if you're unsure. I've had a fair bit of experience and I left it to the pros, just personal preference)

3. Replaced idler and tensioner bearings (Done by tuner)

4. Replaced oil filter (Done myself)

5. Replaced coolant (Done myself)

6. Replaced all the belts (alternator, power steering and AC) (Done by tuner as I CBF'd lol, but it's not to bad)

7. Drained and filled both front and back diffs (Done myself, this was very easy but you have to be careful when lying under the car, make sure you have the proper equipment)

8. Drained and filled the gearbox (Done myself) with RedLine shockproof (very expensive but the beez neez) - again just make sure you have the proper equipment to hoist the car

9. Cleaned and flow tested injectors (You'll have to get it done professionally, cost me $100, very good investment for an R32)

10. Replaced Air filter (I just put in a good quality K&N panel filter, good for a million Km's, just have to blow the dust out every now and then). If you're running pods, just give them a clean/ replace

11. Clean out your air flow meters, ensure you use good quality electric contact cleaner (you can pick up a can from Dick smith)

12. Changed spark plugs (Done myself). This is really easy mate, just make sure you have the right tools and pick up some anti-seize paste from an auto supplier (you put it on the thread of the sparkies so they don't get stuck in there when the engine gets hot)

and if you want to get technical....

13. Check your O2 sensors (on the dump pipes), mine personally had to be replaced, I wouldn't bother though if the car is running okay

If you take ya car to a reputable tuner when they do the more technical stuff, they will be able to tell if there is anything else that needs attention such as brake pads or tire tread condition.

Hope you've been saving ya pennies, a GTR service will be around $1k :),

Cheers,

Sean

Hey mate,

Not sure if you've already started doing the service but I did my 100k service about 2 weeks ago so while it's fresh in my mind I thought I would make a list for ya.....

1. Replaced water pump with new factory item (Done by tuner)

2. Replaced timing belt (Done by tuner - don't attempt this if you're unsure. I've had a fair bit of experience and I left it to the pros, just personal preference)

3. Replaced idler and tensioner bearings (Done by tuner)

4. Replaced oil filter (Done myself)

5. Replaced coolant (Done myself)

6. Replaced all the belts (alternator, power steering and AC) (Done by tuner as I CBF'd lol, but it's not to bad)

7. Drained and filled both front and back diffs (Done myself, this was very easy but you have to be careful when lying under the car, make sure you have the proper equipment)

8. Drained and filled the gearbox (Done myself) with RedLine shockproof (very expensive but the beez neez) - again just make sure you have the proper equipment to hoist the car

9. Cleaned and flow tested injectors (You'll have to get it done professionally, cost me $100, very good investment for an R32)

10. Replaced Air filter (I just put in a good quality K&N panel filter, good for a million Km's, just have to blow the dust out every now and then). If you're running pods, just give them a clean/ replace

11. Clean out your air flow meters, ensure you use good quality electric contact cleaner (you can pick up a can from Dick smith)

12. Changed spark plugs (Done myself). This is really easy mate, just make sure you have the right tools and pick up some anti-seize paste from an auto supplier (you put it on the thread of the sparkies so they don't get stuck in there when the engine gets hot)

and if you want to get technical....

13. Check your O2 sensors (on the dump pipes), mine personally had to be replaced, I wouldn't bother though if the car is running okay

If you take ya car to a reputable tuner when they do the more technical stuff, they will be able to tell if there is anything else that needs attention such as brake pads or tire tread condition.

Hope you've been saving ya pennies, a GTR service will be around $1k :( ,

Cheers,

Sean

Hey mate,

Thx so much for the list. Going be very helpful, now I'll start on my service with a good understanding what to do.

Thx

Amon

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
    • hahah when youtube subscribers are faster than my updates here. Yes some vid from the day is up, here:  Note that as with all track day videos it is boring watching after the bloopers at the start.  The off was a genuine surprise to me, I've literally done a thousand laps around the place and I've never had instability there; basically it rolled into oversteer, slipped, gripped and spat me out. On the way off I mowed down one of the instructor's cones and it sat there all day looking at me with accusing cone eyes as I drove past. 1:13:20 was my fastest lap, and it was in the second session, 3rd lap.  It (or me!) got slower throughout the day as it got hotter.      
    • It sounds like you want what the Toyota Landcruisers have for their roof racks. Wanna know what you end up with? Rust holes in the roof, and water everywhere...
    • Discovered today that if I select reverse first and take my foot off the brake, then select drive, the drive indicator light works and so does the tiptronic gear indicator. 
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Does anyone here have any ideas?   Cheers guys
×
×
  • Create New...