Jump to content
SAU Community

Recommended Posts

Hi,

I got a few manuals through a group buy and have one leftover.

Chassis manual 328 pages.

Engine manual one 262 pages, no. 2 is a little smaller.

Chassis manual is

Clutch

Manual Trans

Auto trans

"Propeller" shaft and final drive

Drive shaft

Front Axle & Front Suspension

Rear Axle & Rear Suspension

Brake System

Steering System

Body exterior

Body interior

Engine Electrical System

Body Electrical System

Auto speed Control Device

Electronic Diagrams

Bought through JPNZ

Victoria only please as I want this picked up from the South Eastern suburbs....(or on an official cruise or similar).

Thanks,

Gareth

Y can't u post it?

Wat if courier came picked it up from ur house?

Hi,

I can post it, but I work long hours (~9:30 - 7PM) and getting to the post office is difficult.

Courier would be better, but for that price you might be able to buy off JPNZ directly JPNZ directly here

Hi Gareth,

Live in richmond willing to pick-up and pay cash let me no when and where.

Mani

PM sent :banana:

Where was everyone during my group buy where I got them even cheaper than this ? :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...