Jump to content
SAU Community

Vvt Cam Gear Timing

Alf

By Alf,
in Engines & Forced Induction

 Share

Recommended Posts

Dorifta Collaborator

Dorifta

Posted
Posted
Does anyone know where the outside part of the inlet VVt cam gear should be when setting the timing at 0 deg?

The back of the cam gear doesnt have any reference marks, see pic

You can tell by the impression the bolt has left on your gear, from ur photo looks like the centre

STATUS Grand Master

STATUS

Posted
Posted

it depends on a few things like head and block decking, if you want them 100% set it via cam lift.

If you want it close just make sure the mark lines up with the timing case backing plate (same as doing cam belt).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Boost cut after swap(RB25DET NEO) R34

      By Kinkstaah · Posted

      I used to have Walbro 255's when they were a pretty common update. (or were they 044? 040?) In any case I had a dirty tank. I thought the tank was good, but I would find the filter would clog in maybe ~50km of driving. If the issue persists, well, your fuel system or tank has crap in it that the pump is sucking up.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi. Ok thanks for the info. I/we do not know what tune is on that Nistune ECU so it is why there is stock ECU and that Nistune is for later when the car is done. I have guy who tunes Nistune and other ECU so i will then take it to him to see and properly tune for the car   And for the update. On 99,9% it is bad fuel pump. Which is wierd cuz it is like 2 years old(brand new walbro 255) and that filter (also brand new) was dirty.  I was alwaya pumped premium(100) on very good petrol station so i dont know how is that possible...  
    • zillah
      Recommendation for engine oil funnel spill free

      By zillah · Posted

      Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Kinkstaah
      Boost cut after swap(RB25DET NEO) R34

      By Kinkstaah · Posted

      Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
×
×
  • Create New...