Jump to content
SAU Community

Recommended Posts

Not sure. I don't think it was standard, but it could well have been an option. Perhaps the easiest way to check is:

Look for the dash light when you turn on the ignition.

Or

Have a quick look under the back of the car for the HICAS unit and control arms...

Dave

as I said before you cHiCaNe; you annoying one.

I've said I never seen R33 GTS-4 with HICAS.

do us favor and take photo of your car rear diff.

then we will tell you if you have Hicas or not.

do you even have light on dash?

R32 GTS-4 yes they have them but no Super hicas, unless its after market. but who in the hell want to install HICAS after market?

and you telling ME I give skyline driver bad name... lol :Bang:

me two yen

cheers

Joe

some people just dont get that there are other people who knows more than him, but instead of listening to information given but instead tell the person they are full of shit or gives bad name...

lol my advice to you chicane... next time listen!!! and think!!! ;)

under the parcel shelf could be one of these things

1.Most likely to be factory amp for speakers

2. rear window wiper controller

3.for 4WD ATTESSA ECU - dont get confused with HICAS ECU.

ps.only bcuz you have Fusespot for 4WD/HICAS in FuseBox etc...etc... doesnt not make you have GTR

  • 3 weeks later...

sorry to break the cheerful banter in here, but i notice dave's R34 has electric HICAS - is this how it is on all '34s? or is it on '33s as well? because my '32 has hydraulic, and it runs off the Power steering pump. I know, coz when the light comes one, i add oil to the PS resevoire and it goes out ! it's the simple things in life, sometimes...

uh, i was actually asking about the hydraulic/Electric thing - i had read the previous thread (i know ho annoying it is when people don't) and am aware that not all 33's have hicas, i was just wondering when they changed to the electric as opposed to hydro.

and my hicas light comes on when i turn on the key - then *hopefully*, all being well, goes out when the engine starts. but i agree with PVA - the drag-links on the rear hubs will be the biggest giveaway!

I didn't have hicas on my old R33, so I can' t really compared the system on a 33 to that of my R34. If anyone has a pic of the 33 system, then we'd be able to compare the two! :)

re the hicas light - same for me: comes on when I turn the key, goes off when the engines started...

There was no HICAS on the R33 GTS-4, one can simply see this if you understand the model lettering.

In R32 models HICAS was included in the 4WD system labelled (N), thus you see BNR32 and ENR32 for GT-R and GTS-4. For other models HICAS was labelled © as seen in ECR32 or HCR32. In the R33 models the HICAS was omited from the GTS-4, thus it was ENR33 and the GT-R was BCNR33. In the R34 models the HICAS label was completely abolished.

From what I understand for Super HICAS there is no lettering, even in the Silvia and 180SX lineup.

There was no HICAS on the R33 GTS-4, one can simply see this if you understand the model lettering.  

Hi Evo_Lee,

Thanks for the informative reply.. makes sense ;) I take it the (B) indicates turbo?

Can someone take a photo of the HICAS system near the diff on an R33?

cheers

chicane

:burnout: :burnout:

Chicane: no the (B) is quite obvious really, the engine fitted. B: RB26, E: RB25 and H: RB20 or more specifically RB20DE. As there is YHR32, YH being RB20E for GTE models; and for the complete picture the FR32, F being CA18i for the GXi models.

R33 and R34 is no different, oh except the HR33 was actually RB20E but they couldn't be bothered nor do I think anyone cares really.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...