Jump to content
SAU Community

Recommended Posts

Just bought another car so its time to get rid of this Pulsar.

Its an N14 SSS

1993 model, one of the "Jap spec" versions with the GTI-R interior

Red

230,000ish K's

Cat-back exhaust

16inch mags (tyres 50%)

Lower springs, not sure of brand

CD player

otherwise standard

I had a brand new radiator installed <5000kms ago because the old one broke

Clutch is ~10,000kms old

Now, the car does have a number of bad points:

The rego ran out mid December '09

There are some dents in the roof from when someone jumped on it at a party

Gear knob and steering wheel are quite warn

Needs new gas struts for the boot ($45 each apparently)

One strip of plastic moulding has come off the left passenger door. I still have it, it just needs to be glued back on.

Has this random stalling issue which seems to happen when slowing down for roundabouts or traffic lights. I could go for a whole week without it happening once, but then the week after it may happen every time i drive it. Its been like that since Ive owned it (last 2 years) and Ive sorta gotten used to it and i just clutch in, and turn the ignition and it starts back up again no problems. Ive done a bit of research and supposedly its got something to do with the earth wire for the fuel pump, but to be honest i couldn't be f**ked spending any more time/money on this car.

Basically Ive been using this car as a daily driver/runabout to get me to and from work and around on the weekends. It still starts first time and with the 2.0L engine has plenty of poke for around the city. I recently upgraded to a Skyline so I have no use for it anymore. With a little TLC this would be a great/reliable little daily or maybe a P platers first car.

I'm looking for $1700

Car is located on the Northern Beaches of Sydney.

PM me here or SMS 0423720348

Cheers,

Pat

03022010.th.jpg

03022010001.th.jpg

03022010002.th.jpg

03022010003.th.jpg

03022010004.th.jpg

Link to comment
https://www.sau.com.au/forums/topic/306687-fs-n14-sss-pulsar-93-syd/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...