Jump to content
SAU Community

Recommended Posts

Hey everyone

For sale a Nissan Skyline GTS25T Series II (1997)

Fitted with full Factor Mspec body kit and GTR rear wing

Located in NSW South West Sydney

Has 88xxx kms on the clock

First owner since compliance

New timing belt/ tensioner/idler/water pump done when car was imported at 55xxxkm in 2007

Upgrades are

• Apexi Pod filter

• Defi boost gauge with Mearcat pod

• Strut brace nolathane

• Bilstine/whitline suspension upgrade inc. F/R camber adjustment (sydneykid kit)

• HKS split dump pipe

• Hks front pipe

• HKS Super Dragger exhaust

• Hi flow metal cat

• R34 GT-T side mount cooler (duct included)

• Nismo shift knob

• Pioneer head unit/Jaycar splits/Jaycar 3way speakers and 4 channel amp

• B pillar floor brace

Also included

Nismo B pillar garnish

Car comes with a set of front shocks with RSR springs

R32 GTR seats included

Cusco strut Brace

Car is in mint condition and one of the best R33 around

$13,500

Contact Norman or Amy 0405244331 or send a PM to me

IMG_1266.jpg

IMG_1271.jpg

IMG_1288.jpg

IMG_1285.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...