Jump to content
SAU Community

Recommended Posts

Hi,

We are doing the R33 RB26DETT motor swap into a US Spec 1998 240SX (S14), and we are going with the Apexi Power FC. I know that the D-Jetro uses the MAP sensors, which would be great for the ultimate tuning control, but does anyone have experience with the tuning?

I have talked with several shops in the USA who won't tune it unless we convert to a single throttle body setup. Could anybody share their knowledge or recommend a better setup?

Thanks!

Chris

Link to comment
https://www.sau.com.au/forums/topic/30785-power-fc-d-jetro-how-hard-to-tune/
Share on other sites

I would use a standard or Pro PFC with upgraded AFM's with the 6 throttle setup intact, as removing these as you probably already know sacrifice fuel economy, but more importantly off-boost drivability and throttle response.

you have already decided to take the first step in degrading your throttle response and drivabilty by using the D-Jetro, so you may as well convert to a single throttle body as well.

The 6 throttle setup is known to make tuning tricky, as the standard throttle body causes some kind of inlet pulsation which the MAP sensor picks up as rapidly fluctuating air flow - This is why most tuners have trouble tuning this setup, however it is very possible, to tune using this setup as it has been done many times before.

At low RPM/airflow levels/load, tune using the TPS versus RPM with the MAP disabled. On boost, at higher RPM, the pulsations will start to diminish and this is where you use the MAP sensor for tuning inputs.

As i have no experience tuning the D-Jetro, i do not know if the D-Jetro is able to do this, but this is apparently the solution.

Hope everything works out :(

edit: this information is mostly second hand and could be incorrect. this is an internet forum, so i hope i dont need to tell you to check the facts first :)

sorry to be off topic but can i ask why dosnt usa have any silvia s15 cant they import them or anything

None of the Silvia's can be imported as the SR20DET motor does not meet emission standards here in the USA. Motorex has been able to import the Skyline after years of tests, etc. Nobody unfortunately is going to go to the expense of crash testing a $15000 car...I wish they would, it would be my dream car....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bummer...yeah i "need" something to "ease" up the work and for my driving it would be enough.    Iam counting the tune "without" turbo. I do not mean "cheap" like something from Temu around 200 USD, "Cheap" is something around 1000 USD? 
    • Starter motors used to use the weight of metal (magnets) to provide torque. Now they use (more) current instead. This. It's completely normal.
    • So thing that had me stumped, but I think is OK....is that when it was up in the air, in neutral I had it running to bleed to coolant while I put the wheels back on. I noticed the rears were turning (slowly) which I'd never seen before 20250928_163512.mp4     Because there had been an issue with clutch slip due to pedal adjustment on the dyno, I assumed there was still and issue so spent some quality time upside down under the dash adjusting the pedal....but no matter what I did the wheels still turned in neutral. Even disconnected the master cylinder to pedal rod and same. In despair, I even removed the clutch slave so there was no chance of any preload causing it.....still happened. So either: 1. Something is not right in the bellhousing, or 2. Its a thing sometimes with cold, thick gearbox oil Internet says it might be 2, I hope so!
    • OK, few more things sorted and it is ready for a shakedown on 10-Oct, with one weird thing. Changed the run in oil and filter for the good stuff. 8l came out, about 8.5 went in with filter so that looks all good. Changed the starter (again), this time for a brand new one, works good. Interesting that the Taaaarks one is shorter than factory but spins harder, I guess electronics have moved on a little in the last 30 years. Will be nice to have a bit of extra space under there. Put the timing cover back on, and noted where the cam gears were set as a record.  Will need to double check the timing but it is pretty close. Also put the coil pack cover and intake snorkel back on. Exhaust Inlet Changed the water out for coolant, bled up nicely. Removed the rear brake pads (well worn factory sumitomo ones!), gave the hardware a good clean and reassembled. I've put bendix XP on the back again because the price is excellent at $150 a set and they worked well on the V37. Front pads have plenty so no issue there
×
×
  • Create New...