Jump to content
SAU Community

Recommended Posts

Hey buddy,

That pc is a bit outdated so finding info about the specs is a bit hard. Hopefully you can help out.

1 x 80gb HDD

1 x 200gb HDD (pretty sure it's SATA)

Are both of them SATA? What's the brand(s) and had any problems?

Radeon X850XT

Is this AGP or PCI-e? Also, how many mb of memory?

Blue Thermaltake Xaser V case with something like 5 built in fans and fan control/temp monitor

Does the fan control/temp monitor work perfectly?

I noticed in one of your pictures the power supply was an Antec. What model is it? How many watts? And how old is it?

EDIT: Could you tell me the model number of the motherboard too? Thanks

Also, where are you located?

Thanks :P

Edited by TheMirror
Link to comment
https://www.sau.com.au/forums/topic/308941-gamer-pc/page/5/#findComment-5525570
Share on other sites

  • Replies 91
  • Created
  • Last Reply

Top Posters In This Topic

Hey buddy,

That pc is a bit outdated so finding info about the specs is a bit hard. Hopefully you can help out.

Are both of them SATA? What's the brand(s) and had any problems?

Is this AGP or PCI-e? Also, how many mb of memory?

Does the fan control/temp monitor work perfectly?

I noticed in one of your pictures the power supply was an Antec. What model is it? How many watts? And how old is it?

EDIT: Could you tell me the model number of the motherboard too? Thanks

Also, where are you located?

Thanks :D

Sorry just saw this post now...Best to PM me so I see it quicker

1. Only the 200gb is SATA, The brand is Western Digital (Model number - WD2000JS-98MHB0)

The 80gb is Western Digital as well (Model number - WD800JB-00ETA0)

Never had an issue with either of them..

2.The video card is PCI-E and 256mb DDR3

3.Fan controller works fine. From memory I disconnected one of fan speed sensors because one of the fans wasn't compatible with the sensor or something and obviously the controller thought the fan was stopped, which it wasn't.

4.The power supply is an Antec True 480 (480W). Can't remember how old it is, but it's newer than the rest of the computer because my old one died so I replaced it with the Antec...

5.Motherboard is a Gigabyte GA-K8NF-9

6. I'm located in Hoppers Crossing, western suburbs of Melbourne...

Think that's all of em...Like I said if there's anything else you want to know, it's best to PM me for a faster reply :)

Link to comment
https://www.sau.com.au/forums/topic/308941-gamer-pc/page/5/#findComment-5535494
Share on other sites

  • 4 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I tried the next one up from 600k ohms which is 60M on my multimeter and all readings came out as 0.00 ohms so right now the most accurate is 600k ohms with only a 0.1 ohms difference between coils. Three coils read 1.4 ohms and the other three read 1.5 ohms.
    • surely that is a control arm, not a sway bar. In any case, visual condition should not be an issue, excessive movement under load (eg with a big pry bar) would be the issue. I can't see 99.999% of pink slip places even looking, let alone trying to test it
    • I attached the image of the only thing I found, nothing to do with ohms in the manual only torque values etc. However, being they are so close to each other I am almost certain they are good. Tomorrow I will test the spark plugs while I am there. and look at the ECU connections.
    • Hi Gents. Do u know what 18rim will fit under R32 GTST with no modification of current setup I have. I have buddy Club P1 17x8 on front and 17x9 rears and they fit well.   Will an 18x9 on 35 off set with 235 tyres up front fit? ON the Rears i can run the rim size n fit 255 or 245? or i got option to get 18x9.5 on 35+ Offset n 265?   CHeers
    • And, when measuring and getting <2 ohms, perhaps chose the next larger range than that, rather than something with a k in it!
×
×
  • Create New...