Jump to content
SAU Community

Recommended Posts

Hi everyone,

My R34 GT-T is up for sale as my race car needs some money thrown at it. I am the second owner of the car since it was brought into the country in 2005. The first owner did some simple modifications as listed below.

Details:

Make: Nissan

Model: Skyline R34 GT-T Turbo

Engine:RB25det Neo

Body: Coupe

Trans: Tiptronic Auto

Colour: White

ODO: 123,000kms

REGO: Jan 2011

Modifications:

- Cooling Pro Front mount intercooler

- Pod Air filter

- Fujitsubo 3.5inch stainless steel cat back exhaust (I have the original exhaust and will be given to the new owner)

- Blitz Information ECU thingy...(it displays water temp, ignition etc)

- Apexi Pen turbo timer

- Pivot speed display thingy

- Turbosmart boost controller (knob screwed all the way on low)

- Blistein shocks (not sure on springs but not low)

Other

- Kenwood mp3 player + kenwood Amp

- Reverse sensor installed for those who need help reversing :down:

For those who know me or have bought cars from me in the past, they would tell you how picky and how particular I am with my cars. Mechanically, I cannot fault the car in anyway. The interior is immaculate and exterior is in great condition. The only bad point on the exterior is the boot lid...The previous owner had put some aftermarket rear wing on it so I have placed small black grommets to cover the holes where the wing used to be. The stock rear wing is now back in place. (I'm keeping the aftermarket rear wing...its now on my race car). The other thing I should mention is that the drivers side front guard and the front bumper bar were damaged but have been replaced and painted.

The car has just been serviced. The engine oil has just been changed using Royal Purple 10w-40 oil and the transmission oil was also changed.

PRICE: $14,900 ONO. The car comes with 12 month rego and nothing to more spend!!!

It's priced like this as I need the money for my race car but I WON'T be giving the car away so no time wasters or low ballers. If I have to wait for the right buyer, then the race car will also have to wait.

Location: Sydney, NSW

Contact: pm or call me on 0407 931 097

post-6485-1266660184_thumb.jpg

post-6485-1266660397_thumb.jpg

post-6485-1266660450_thumb.jpg

post-6485-1266660705_thumb.jpg

post-6485-1266660745_thumb.jpg

post-6485-1266660808_thumb.jpg

post-6485-1266660834_thumb.jpg

post-6485-1266660893_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/308989-nissan-skyline-r34-gt-t-turbo-coupe/
Share on other sites

FYI, the Blitz gadget is the BLITZ R-VIT Type II monitor (this reads information in realtime from the vehicle ECU) and the other thing is the Pivot Speed meter

Congrats on the sale. Someone picked themselves up a nice looking and well priced r34 by the looks of it .......

yep they sure did :cheers: ...thanks for the nice comments :thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
    • Hi all,I already introduced myself in the Victoria section, but only saw this section now lol XD New to forums and new to skylines. Hoping to buy my new skyline within October
×
×
  • Create New...