Jump to content
SAU Community

R32, R33 Ect Parts Cheapp, Need It All Gonee

boz_soljah
 Share

Recommended Posts

boz_soljah Mentor

boz_soljah

Posted
Posted

i need to get rid of all these parts

Going CHEAP

r32 5 Stud conversion $400 (hubs, caster arms, discs, calipers, ect)

rb20det manual box $400 (short shifter, was on drag car, done low 11z, poped wheelies, got photos)

r32 full rear diff cradle assembly $200 ( diff, cradle arms, ectt)

R32 gtst bonnet, primer $100

r32 gtst bonnet, dark blue $100

r32 type m boot with spoiler $100

r32 type m rear bar $50

r32 right door $50

r32 left door $50

r32 gtst seats, $150 set, front and rear

r32 guards $50 each, right and left

Rb20det engine parts, ask if you need

rb20det head, complete cams ectt $250

lots of r32 interior pieces, ask if u need something

R33 gtst diff $100

R33 right door $50

r33 right guard $50

r33 s2 seats $100 front only

r33 s2 dash, mint condition, airbag included $100

lots if interior pieces, askk if u need something

s13 Original Aero Front Bar $400 need a bit of repair, still in one piece, has zip tie stiching

Full locker Diff, 4:11 ratio, for r31 or vl, $300, with discs, calipers, shockers, ectt was on drag r31, done wheelies, low 12z

R32 rear cut, shell only $250

Melbourne

Western Suburbs,

0411980023

boz_soljah Mentor

boz_soljah

Posted
  • Author
Posted
R32 interior blower/fan and a/c evaporator under dash posted to 4210?

Thanks Sam

dont have them, sorry

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • Dose Pipe Sutututu
      Chris' Toyota Mark ii JZX110

      By Dose Pipe Sutututu · Posted

      I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • MBS206
      Starter motor replacment teeth count.

      By MBS206 · Posted

      I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...