Jump to content
SAU Community

Recommended Posts

hey guys i have series 1 r33 was just wondering what power i could expect im chasing around 350hp im getting a tune next week just want to know a rough estimate of what i could get.. here are the mods..

-rb25det

-high flowed 33 turbo

-fmic

-3' turbo back exhaust

-700hp fuel pump

- split fire coil packs

-550cc injectors

-malpassi adjustable fuel reg

-wolf 3d v4

-10 puk clutch

-hks mushroom pod

-iridium spark plugs

looking to get it tuned on bout 16-17psi .. let me know what you all think what power figures i should expect.

im nto sure what high flow it is.. but i was told it was a stock highflow just been rebuilt and ive checked the turbo out it .. got my mechanic to take the dump of and put a magnet on the rear wheel ..ooh and 230-260kw sounds goood :)

Edited by smitty 33
hey mate why should i get rid of the malpassi reg?? just curious ? i just bought the thing and got it installed lol ..

Main reason is that a tune is dependant on the fuel pressure it is running at. So if the malpassi fuel reg is running a particular fuel pressure then you go and change it later on, the tune will be out.

Running the stock fuel reg just removes one other thing that can be incorrect. Genuine brands are normally of very good quality.

but also if i never changed the reg ? would it matter?

a malpassi is never going to be more reliable then a genuine nissan one.

plus if you dont raise the fuel pressure over standard then whats the point in having it.

my theory is you want to keep as match factory stuff as possible, minimal mods required for a safe reliable setup.

your 550cc injectors will supply plenty of fuel for you power level so there is no problem there.

Edited by Harey

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...