Jump to content
SAU Community

Wrecked R32 Skyline + Rb20det Parts

Nissan r32
 Share

Recommended Posts

Nissan r32 Collaborator

Nissan r32

Posted
Posted

All parts are out of a 1993 model R32 Skyline 2 door. Parts include:

Drivers seat $50

Rear Seat $60

Rear centre seat belt $20

Window wiper motor $40

Air con pipe (firewall to compresser) $20

GTST Bonnet (Silver) $100

Drivers door (Black) with glass and power window motor $100

Boot Lid (Black) Slight repairable damage $30

Stock dump pipe (Turbo to cat) $30

Stock Cat $20

LSD Diff centre $180

Manual Tail shaft $100

Brake Booster $40

Rear Brake calipers + discs $60 the pair

® Rear quarter trim (Bottom half) $20

Scuff plates + Clips $30pair

Pioneer detach face stereo 200w $20

Base 10" sub in box 500w $20

Indicater stalk + horn wire (Complete unit) $100

Boss kit $30

Front strut brace $30

Interior light $10

Rear view mirror $10

(L) Electric mirror (Black) $50

Door check straps both $20

All door lock rods + Clips (both doors) $20

Electric sunroof switch + Interior light $50

Centre dash tunnel surround $10

Passenger glove box door $20

Climate Control Unit $100

Nismo gear knob + handbrake lever both new in box (Never used) $50

Drivers side plastic guard liner $20

Space saver spare wheel $40

Timber plate to cover spare wheel $20

Stereo brackets + Compartment $20

Fuel Flap (Black) $40

Fuel Cap (Nissan) $10

Number plate lights + wiring and fuses $20

Lots of RB20det Engine parts: Motor only done 82000km:

Crossover Pipe with BOV mount + gasket $50

Top + Bottom Radiator hoses, near new $30

Clutch Fan $60

Coil packs x6 $80

Coil pack plates + bolts (to hold coil packs in place) $40

Igniter $40

Pulley belts x 2 $20

Throttle body (Complete) $50

Inlet manifold $80

Stock turbo + Wastegate actuator $350

Stock turbo oil + Coolant lines $30

Crank Angle Sensor + Bolts $50

Stock front mount under bonnet piping (all) $60

Alternator (Gen Nissan) $60

Power Steering pump with bracket $100

Power steering reservoir $20

Century Battery, near new $50

Air flow to BOV Steel pipe $20

Engine mounts $50 each

Harmonic Balancer $80

Fly wheel $60

Starter motor $80

RB20det Engine Block and head Complete $500 Good for someone who needs a bare block and head

and can swap all there stuff over onto. E.G: If your RB20 is blown, heres a good motor for you,

just need to swap all your stuff over.

RB20det 5 speed Gearbox (No crunches, or noises) Very clean, smooth and quiet box $500

Im located in Ashfield (Sydney)

Postage can be arranged at buyers expense

PM or contact me on 0415126075

Cheers Sam

Link to comment
Share on other sites
  • 1 month later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Chris_Guthrie
      Misfire/stalling issues

      By Chris_Guthrie · Posted

      30amp*
    • Komdotkom
      Rob's S Chassis track cars. Now with more s15 and less 180sx

      By Komdotkom · Posted

      I'll chime in here with my experience. Motec is great if you have the money and know a good person to support you. They don't really offer retail support and the dealers make SFA margin on the product, so the business model is setup for you to be supported by a dealer. I'm lucky enough to know a guy who's ex Motec and very generous with his time and is a total boffin. In addition to that, I also use Brad Sherriff who's an absolute legend to work with. The downside to Motec is the software isn't very intuitive, pay to play, poor/limited online support and costly upgrades.  I've not owned an Emtron myself but a good friend runs a performance workshop in Melbourne who is an Emtron dealer. They won't be fitting any more to customer cars because of the poor level of knowledge within the Emtron support team and lack of ability to solve issues with the platform. Not to mention the circumstances around the establishment of the product and company in the first place. I've run Motec's since the old M8's back in the early 2000's so I'm certainly not without a bias but I look at it like this. Everyone acknowledges Motec as the best consumer grade product without spending mega dollars on Bosch Motorsport / Life Racing and so on. When you consider the real cost of your car (not what you tell your mrs) the cost difference between an Emtron and a Motec is tiny, why would you compromise over a few hundred dollars?
    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      Closer to getting the shit box back on the road. That long hose, took 2 months to acquire. However the rest were all already to go same week I ordered them. For those playing at home, that long hose is for a RB25DE N/A motor, as they don't run a water/oil heat exchanger, the hoses underneath the plenum are much more elegant and not a maze of shit.
    • Kinkstaah
      R34 350z lsd conversion (speedo)

      By Kinkstaah · Posted

      One thing you may be able to leverage is the fact that the R34 N/A has the same setup as a S15. The S15 also is a car that gets 350Z diff swapped, so they will also likely have this problem. The caveat of course is it's possible the dash is different between the R34 NA and the S15, but the subframe/sensors/axles/diff setup are the same. I can't remember now as it's been too long, but I don't generally think people need to swap dashes between the N/A dash and the turbo dash when they do things like change the gearbox out, turbo their car, manual swap it, it's just not something I've seen mentioned so this could be compatible.
    • Dose Pipe Sutututu
      what is this part? behind the BS module

      By Dose Pipe Sutututu · Posted

      Just need to weld it in and done   
×
×
  • Create New...